Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Nissan X-Trail 2005 2006 Approved 2006 EX
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download EX documenatation <<
Text preview - extract from the document
EXHAUST SYSTEM
B ENGINE
A
SECTION
EXHAUST SYSTEM
EX EX
C
D
E
CONTENTS
EXHAUST SYSTEM .................................................. 2
. Checking Exhaust System ....................................... 2
. F
Removal and Installation ......................................... 3
.
REMOVAL ............................................................ 3
.
INSTALLATION .................................................... 3
. G
INSPECTION AFTER INSTALLATION ................. 4 .
H
I
J
K
L
M
Revision: 2006 July EX-1 2006 X-Trail
EXHAUST SYSTEM
EXHAUST SYSTEM PFP:20100
Checking Exhaust System ABS00D0S
Check exhaust pipes, muffler and mounting for improper attachment,
leaks, cracks, damage or deterioration.
q If necessary, repair or replace damaged parts.
SMA211A
Revision: 2006 July EX-2 2006 X-Trail
EXHAUST SYSTEM
Removal and Installation ABS00D0T
A
CAUTION:
q Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance and shape.
q Perform the operation with the exhaust system fully cooled down because the system will be hot EX
just after engine stops.
q Be careful not to cut your hand on the insulator edge.
C
D
E
F
G
H
I
J
K
PBIC2732E
*: In regard to the notation of torque in the figure, "NEW" shows an ISO standard, "OLD" shows a conventional standard, and the mea-
surements of hexagonal width across flats are in parentheses.
L
1. Main muffler 2. Mounting rubber 3. Spring
4. Gasket 5. Three way catalyst 6. Exhaust front tube
7. Seal bearing 8. Mounting rubber bracket 9. Mounting bracket M
10. Exhaust center tube
REMOVAL
Disconnect each joint and mounting.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
q Always replace exhaust tube gaskets and seal bearings with new ones when reassembling.
q If heat insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the heat
insulator, remove them.
q When installing heat insulator avoid large gaps or interference between heat insulator and each
exhaust pipe.
q Remove deposits from the sealing surface of each connection. Connect them securely to avoid
gas leakage.
Revision: 2006 July EX-3 2006 X-Trail
EXHAUST SYSTEM
q Temporarily tighten all mounting nuts and bolts. Check each part for unusual interference, and
then tighten them to the specified torque.
q When installing each mounting rubber, avoid twisting or unusual extension in up/down and right/
left directions.
Install seal bearings at exhaust front tube and main muffler as follows.
CAUTION:
q Do not mix the bolt and spring for seal bearing as the dimension is different for each seal bearing.
Seal Bearing (Exhaust Front Tube Side)
Insert seal bearing in the direction shown in the figure.
1. Securely insert seal bearing into exhaust manifold and three
way catalyst assembly side in the direction as shown in the fig-
ure.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. Make sure that mounting bolts do not interference with flange of
exhaust front tube.
PBIC2274E
Seal Bearing (Main Muffler Side)
1. Securely insert seal bearing into exhaust center tube side in the
direction as shown in the figure.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2. Make sure that mounting bolts do not interference with flange of
main muffler.
PBIC2275E
INSPECTION AFTER INSTALLATION
q With engine running, check exhaust tube joints for gas leakage and unusual noises.
q Make sure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
Revision: 2006 July EX-4 2006 X-Trail
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo