Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 1995-1999 Approved Subaru Legacy 1995 1995 Service Manual ENGINE SECTION ENGINE LUBRICATION SYSTEM MSA5TCD95L5476
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download MSA5TCD95L5476 documenatation <<
Text preview - extract from the document
2-4 SERVICE PROCEDURE
2. Oil Pan and Oil Strainer
2. Oil Pan and Oil Strainer
A: REMOVAL
1) Remove front wheels.
2) Remove air intake duct.
3) Disconnect connector from front oxygen sensor.
G2M0544
4) Remove pitching stopper.
G2M0295
5) Remove radiator upper brackets.
B2M0320
6) Support engine with a lifting device and wire ropes.
7) Lift-up the vehicle.
CAUTION:
At this time, raise up wire ropes.
B2M0053
8) Drain engine oil.
Set container under the vehicle, and remove drain plug
from oil pan.
G2M0066
8
SERVICE PROCEDURE 2-4
2. Oil Pan and Oil Strainer
9) Disconnect connector from rear oxygen sensor.
B2M0312
10) Remove front exhaust pipe.
(1) Separate front catalytic converter from center
exhaust pipe.
(2) Remove front exhaust pipe from engine.
(3) Remove bolt which installs front exhaust pipe on
bracket.
B2M0054
11) Remove nuts which install front cushion rubber onto
front crossmember.
G2M0293
12) Remove bolts which install oil pan on cylinder block
while raising up engine.
13) Insert oil pan cutter blade between cylinder block-to-oil
pan clearance.
CAUTION:
Do not use a screwdriver or similar tool in place of oil
pan cutter.
G2M0081
14) Separate oil strainer from oil strainer stay.
G2M0082
9
2-4 SERVICE PROCEDURE
2. Oil Pan and Oil Strainer
15) Remove oil strainer.
G2M0376
16) Remove baffle plate and oil strainer stay.
G2M0377
B: INSPECTION
By visual check make sure oil pan, oil strainer, oil strainer
stay and baffle plate are not damaged.
C: INSTALLATION
CAUTION:
Before installing oil pan, clean sealant from oil and
engine block.
1) Install baffle plate and oil strainer stay.
Tightening torque:
5 Nm (0.5 kg-m, 3.6 ft-lb)
G2M0377
2) Install oil strainer onto baffle plate.
CAUTION:
Replace O-ring with a new one.
Tightening torque:
9.8 Nm (1.0 kg-m, 7 ft-lb)
G2M0376
10
SERVICE PROCEDURE 2-4
2. Oil Pan and Oil Strainer
3) Hold oil strainer to oil strainer stay.
Tightening torque:
9.8 Nm (1.0 kg-m, 7 ft-lb)
G2M0082
4) Apply fluid packing to mating surfaces and install oil
pan.
Fluid packing:
THREE BOND 1207C or equivalent
G2M0084
5) Tighten bolts which install oil pan onto engine block.
Tightening torque:
9.8 Nm (1.0 kg-m, 7 ft-lb)
G2M0081
6) Lower engine onto front crossmember.
7) Tighten nuts which install front cushion rubber onto front
crossmember.
Tightening torque:
69◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo