Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 1995-1999 Approved Subaru Legacy 1995 1995 Service Manual MECHANICAL COMPONENTS SECTION WHEELS AND AXLES MSA5TCD95L5639

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.



Image preview - the first page of the document



>> Download MSA5TCD95L5639 documenatation <<

Text preview - extract from the document

4-2                                       SERVICE PROCEDURE
6. Replacement of Rear DOJ and BJ Boots


                                              6. Replacement of Rear DOJ and BJ
                                              Boots
                                              A: REMOVAL
                                              1) Disconnect ground cable from battery.
                                              2) Lift-up vehicle, and remove rear wheel cap and wheels.
                                              NOTE:
                                              Axle nut need not be removed.
                                              3) Remove A.B.S. sensor clamps and parking brake cable
                                              bracket.
                                              4) Disconnect stabilizer link from lateral link.
                                              5) Remove bolts which secure lateral link assembly to rear
                                              housing.
                                              6) Remove bolts which secure trailing link assembly to
                                              rear housing.
                                              7) Remove crossmember reinforcement lower from cross-
                                              member (4 door model only).




                                              8) Remove DOJ from rear differential using ST.
                                              ST     28099PA100 DRIVE SHAFT REMOVER
                                              NOTE:
                                              The side spline shaft circlip comes out together with the
                                              shaft.




                                    G4M0994


                                              CAUTION:
                                              Be careful not to damage side bearing retainer. Always
                                              use bolt as shown in figure, as supporting point for ST
                                              during removal.
                                              ST    28099PA100 DRIVE SHAFT REMOVER




                                    G4M0995


                                              B: INSTALLATION
                                              1) Install DOJ and BJ boots to drive shaft.
                                              




                                                    42
   SERVICE PROCEDURE                                               4-2
                                 6. Replacement of Rear DOJ and BJ Boots


           2) Using ST, install DOJ into differential.
           ST    28099PA090 SIDE OIL SEAL PROTECTOR




B4M0549A


           3) Insert DOJ spline end into bore of side oil seal, and
           remove ST.
           CAUTION:
           Do not allow DOJ splines to damage side oil seal.
           ST    28099PA090 SIDE OIL SEAL PROTECTOR




B4M0550A


           4) Align DOJ and differential splines.
           5) Push housing to insert DOJ into differential.
           NOTE:
           Make sure DOJ is inserted properly.




G3M0050


           CAUTION:
           Discard old self-locking nut. Replace with a new one.
           6) Connect rear housing assembly to trailing link
           assembly, and tighten self-locking nut.
           7) Connect rear housing assembly to lateral link assembly,
           and tighten self-locking nut.
           8) Connect stabilizer link to lateral link.
           9) Install crossmember reinforcement lower to crossmem-
           ber (4 door model only).
           10) Install A.B.S. sensor clamps and parking brake cable
           bracket.




                 43

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo