Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 1995-1999 Approved Subaru Legacy 1997 1997 Service Manual ELECTRICAL SECTION BODY ELECTRICAL SYSTEM MSA5TCD97L3882

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download MSA5TCD97L3882 documenatation <<

Text preview - extract from the document

SERVICE PROCEDURE 6-2
11. Rear Wiper and Washer - 12. Rear Window Defogger

3) Reconnect battery and ensure that wiper motor stops at
"AUTO STOP" after it has been operated.

B6M0169

3. REAR WIPER RELAY
1) Connect battery to terminal No. 1 and ground terminal
No. 2.
2) Check continuity between terminals as indicated in
table below:
When current flows. Between terminals Continuity does not
No. 3 and No. 5 exist.
Between terminals Continuity exists.
No. 3 and No. 4
When current does not flow. Between terminals Continuity exists.
No. 3 and No. 5
Between terminals Continuity does not
No. 3 and No. 4 exist.
Between terminals Continuity exists.
No. 1 and No. 2

G6M0134

4. WASHER MOTOR
Apply battery voltage between terminals of washer motor
connector and check that washer motor operates.

B6M0111

12. Rear Window Defogger
A: REMOVAL AND INSTALLATION
1. DEFOGGER SWITCH
1) Remove screws which secure meter visor.
2) Remove meter visor from instrument panel while dis-
connecting connectors.
3) Remove rear window defogger switch from meter visor.

31
6-2 SERVICE PROCEDURE
12. Rear Window Defogger

B: INSPECTION
1. DEFOGGER SWITCH
Move rear window defogger switch to each position and
check continuity between terminals as indicated in table
below:
Terminal
3 5 1 4 2
Switch position
OFF k k
ON k k k k k
B6M0119

2. DEFOGGER RELAY
Check continuity between terminals as indicated in table
below, when connecting the battery to terminal No. 1 and
No. 3.
Between terminals
When current flows. Continuity exists.
No. 2 and No. 4
Between terminals Continuity does not
No. 2 and No. 4 exist.
When current does not flow.
Between terminals
Continuity exists.
No. 1 and No. 3

G6M0112

3. HEAT WIRES
1) Start the engine so that battery is being charged.
2) Turn defogger switch to ON.
3) Check each heat wire at its center position for discon-
tinuity by setting direct current voltmeter.
Normal indication is about 6 volts.

G6M0135

NOTE:
When measuring voltage, wind a piece of tin foil around the
tip of the tester probe and press the foil against the wire
with your finger.

G6M0136

32
SERVICE PROCEDURE 6-2
12. Rear Window Defogger - 13. Combination Meter

4) When tester indicates 12 volts when its probe reaches
point "A", a broken circuit occurs between point "A" and the
negative terminal. Slowly move tester probe toward the
negative terminal while contacting it on heat wire to locate
point where tester indication changes abruptly (0 volts).
This is the point where a broken circuit occurs.
When tester indicates 0 volts when its probe reaches point
"A", a broken circuit occurs between point "A" and the posi-
tive terminal. Locate a point where tester indication
changes abruptly (12 volts) while slowly moving tester
probe toward the positive terminal.

G6M0137

C: REPAIR
1) Clean broken wire and its surrounding area.
2) Cut off slit on (used) thin film by 0.5 mm (0.020 in) width
and 10 mm (0.39 in) length.
3) Place the slit on glass along the broken wire, and
deposit conductive silver composition (DUPONT No. 4817)
on the broken portion.
4) Dry out the deposited portion.
5) Inspect the repaired wire for continuity.
G6M0138

13. Combination Meter
A: REMOVAL AND INSTALLATION
1. COMBINATION METER
1) Move steering wheel fully down.
2) Remove screws which secure meter visor.
3) Remove visor from instrument panel.
4) Disconnect connectors from meter visor.

B6M0120

5) Remove screws which secure combination meter, and
pull combination meter out.
6) Disconnect connectors from back of combination meter.
CAUTION:
When installing combination meter, be sure to connect
connectors to backside of combination meter.

B6M0121

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo