Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 1995-1999 Approved Subaru Legacy 1997 1997 Service Manual ELECTRICAL SECTION BODY ELECTRICAL SYSTEM MSA5TCD97L3883
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download MSA5TCD97L3883 documenatation <<
Text preview - extract from the document
SERVICE PROCEDURE 6-2
12. Rear Window Defogger - 13. Combination Meter
4) When tester indicates 12 volts when its probe reaches
point "A", a broken circuit occurs between point "A" and the
negative terminal. Slowly move tester probe toward the
negative terminal while contacting it on heat wire to locate
point where tester indication changes abruptly (0 volts).
This is the point where a broken circuit occurs.
When tester indicates 0 volts when its probe reaches point
"A", a broken circuit occurs between point "A" and the posi-
tive terminal. Locate a point where tester indication
changes abruptly (12 volts) while slowly moving tester
probe toward the positive terminal.
G6M0137
C: REPAIR
1) Clean broken wire and its surrounding area.
2) Cut off slit on (used) thin film by 0.5 mm (0.020 in) width
and 10 mm (0.39 in) length.
3) Place the slit on glass along the broken wire, and
deposit conductive silver composition (DUPONT No. 4817)
on the broken portion.
4) Dry out the deposited portion.
5) Inspect the repaired wire for continuity.
G6M0138
13. Combination Meter
A: REMOVAL AND INSTALLATION
1. COMBINATION METER
1) Move steering wheel fully down.
2) Remove screws which secure meter visor.
3) Remove visor from instrument panel.
4) Disconnect connectors from meter visor.
B6M0120
5) Remove screws which secure combination meter, and
pull combination meter out.
6) Disconnect connectors from back of combination meter.
CAUTION:
When installing combination meter, be sure to connect
connectors to backside of combination meter.
B6M0121
33
6-2 SERVICE PROCEDURE
13. Combination Meter
B: BULB REPLACEMENT
B6M0761A
k
1 Tachometer and temperature k
8 Seat belt k
16 Speedometer and fuel gauge illumi-
gauge illumination k
9 Door open (Front-Left) nation
k
2 Oil pressure k
10 Door open (Rear-Right) k
17 Low fuel
k
3 CHECK ENGINE (Malfunction Indi- k
11 Door open (Rear-Left) k
18 Charge
cator Light) k
12 Rear gate open (Wagon) k
19 Brake fluid level/parking brake
k
4 Tachometer illumination k
13 TCS (Operation indicator) k
20 FWD
k
5 Turn signal (RH) (TAIWAN model) k
21 AT oil temperature
k
6 Headlight beam k
14 Turn signal (LH) k
22 ABS
k
7 Door open (Front-Right) k
15 Speedometer illumination k
23 TCS (Warning) (TAIWAN model)
34
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo