Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 1995-1999 Approved Subaru Legacy 1998 1998 Service Manual ENGINE SECTION FUEL SYSTEM MSA5TCD98L20937

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document

>> Download MSA5TCD98L20937 documenatation <<

Text preview - extract from the document

SERVICE PROCEDURE [W3A1] 2-8
3. Fuel Filler Pipe

3. Fuel Filler Pipe 5) Remove screws which install fuel filler pipe on
filler lid open.
A: REMOVAL
1. 2200 cc FWD MODEL, 2500 cc MODEL
AND TAIWAN SPEC. VEHICLES
1) Release fuel pressure.
2) Open fuel flap lid, and remove fuel filler cap.

B2M1747

6) Remove wheel nuts of rear right side.
7) Lift-up the vehicle.
8) Remove rear right side wheel.

B2M1746

3) Disconnect battery ground cable.

B2M1748

9) Remove bolts which install protector cover on
body.
B2M1723

4) Drain fuel from fuel tank.

B2M1894

10) While releasing the under side of protector
G2M0345
cover from hook, remove it.

B2M1750A

35
2-8 [W3A2] SERVICE PROCEDURE
3. Fuel Filler Pipe

11) Remove bolts which hold fuel filler pipe 2. 2200 cc AWD EXCEPT TAIWAN SPEC.
bracket. VEHICLES
1) Release fuel pressure.
2) Open fuel flap lid, and remove fuel filler cap.

B2M1895

12) Move clip, and disconnect air vent hose from
air vent pipe. B2M1746

3) Disconnect battery ground cable.

B2M1896

13) Loosen clamp, and separate air vent hose (B) B2M1723
and fuel filler hose (A) from air vent and fuel filler
4) Drain fuel from fuel tank.
pipe.

G2M0345
B2M1193B

14) Remove fuel filler pipe to under side of the 5) Remove screws which install fuel filler pipe on
filler lid open.
vehicle.

B2M1747
B2M1756

36
SERVICE PROCEDURE [W3A2] 2-8
3. Fuel Filler Pipe

6) Remove wheel nuts of rear right side. 12) Remove bolts which hold fuel filler pipe
7) Lift-up the vehicle. bracket.
8) Remove rear right side wheel.

B2M1752
B2M1748
13) Lift-up the vehicle more.
9) Remove bolts which install protector cover on 14) Remove two evaporation hoses from clip.
body.

B2M1753
B2M1749
15) Disconnect evaporation hose from joint pipe.
10) While releasing the under side of protector
cover from hook, remove it.

B2M1754

B2M1750A
16) Loosen clamp, and disconnect fuel filler hose
from fuel filler pipe.
11) Disconnect evaporation hoses from pipes.

B2M1745
B2M1751

37
2-8 [W3B1] SERVICE PROCEDURE
3. Fuel Filler Pipe

17) Remove fuel filler pipe to under side of 3) Insert air vent hose approximately 25 to 30 mm
vehicle. (0.98 to 1.18 in) into the lower end of air vent pipe
and hold clip.
L = 25 -- 30 mm (0.98 -- 1.18 in)

B2M1756

B: INSTALLATION B2M1195A

1. 2200 cc FWD MODEL, 2500 cc MODEL (1) Hose
AND TAIWAN SPEC. VEHICLES (2) Clip
(3) Pipe
1) Set fuel filler pipe from under side of vehicle,
and hold it on fuel filler flap open. 4) Lower the vehicle.
5) Temporarily tighten screws which install fuel
filler pipe on filler lid open.

B2M1756

2) Insert fuel filler hose (A) approximately 25 to 30 B2M1747
mm (0.98 to 1.18 in) over the lower end of fuel filler
pipe and tighten clamp. 6) Connect air vent hose to air vent pipe.
CAUTION:
Do not allow clips to touch air vent hose (B)
and rear suspension crossmember.

B2M1896

B2M1193B

38
SERVICE PROCEDURE [W3B1] 2-8
3. Fuel Filler Pipe

7) Tighten bolt which holds fuel filler pipe on body. 13) Tighten screws which install fuel filler pipe on
filler lid open.

B2M1895
B2M1747
8) Lift-up the vehicle.
9) Tighten clamp bolt which holds fuel filler hose. 14) Install rear right wheel.

B2M1193B B2M1748

10) Lower the vehicle. 15) Install fuel filler cap.
11) While holding the under side of protector cover
on bracket, install protector cover.

B2M1746

B2M1750A
16) Install fuel pump, and connect connector and
fuel hoses.
12) Tighten bolts which install protector cover on
body.

B2M0047

B2M1894

39
2-8 [W3B2] SERVICE PROCEDURE
3. Fuel Filler Pipe

17) Install fuel sub meter unit, and connect con- 3) Lower the vehicle.
nector and jet pump hose. 4) Temporarily tighten screws which install fuel
filler pipe on filler lid open.

G2M0864
B2M1747
18) Connect battery ground terminal.
5) Tighten bolt which holds fuel filler pipe on body.

B2M1723
B2M1752

2. 2200 cc AWD EXCEPT TAIWAN SPEC. 6) Connect evaporation hoses to pipes.
VEHICLES
1) Set fuel filler pipe from under side of vehicle,
and hold it on fuel filler flap open.

B2M1751

7) Lift-up the vehicle.
8) Tighten clamp bolt which holds fuel filler hose.
B2M1756

2) Connect fuel filler pipe into fuel filler hose.

B2M1745

B2M1757

40
SERVICE PROCEDURE [W3B2] 2-8
3. Fuel Filler Pipe

9) Install two evaporation hoses to clip. 14) Tighten screws which install fuel filler pipe on
filler lid open.

B2M1753
B2M1747
10) Connect evaporation hose to joint pipe.
15) Install rear right wheel.

B2M1754
B2M1748
11) Lower the vehicle.
12) While holding the under side of protector 16) Install fuel filler cap.
cover on bracket, install it.

B2M1746
B2M1750A
17) Install fuel pump, and connect connector and
13) Tighten bolts which install protector cover on fuel hoses.
body.

B2M0047
B2M1749

41
2-8 [W3C0] SERVICE PROCEDURE
3. Fuel Filler Pipe

18) Install fuel sub meter unit, and connect con- 2) Remove bolt which installs joint pipe on fuel
nector and jet pump hose. filler pipe.

G2M0864 B2M1759

19) Connect battery ground terminal. 3) Disconnect evaporation hose from fuel filler
pipe.

B2M1723
B2M1760

C: DISASSEMBLY (2200 cc AWD 4) Disconnect evaporation hoses from shut valve.
EXCEPT TAIWAN SPEC. VEHICLES)
1) Move clip, and disconnect evaporation hose
from joint pipe.

B2M1761

5) Remove shut valve from fuel filler pipe.

B2M1758

B2M1762

42
SERVICE PROCEDURE [W3D0] 2-8
3. Fuel Filler Pipe

D: ASSEMBLY (2200 cc AWD 5) Install evaporation pipe to fuel filler pipe.
EXCEPT TAIWAN SPEC. VEHICLES)
1) Install shut valve on fuel filler pipe.
Tightening torque:
4.4

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo