Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 1995-1999 Approved Subaru Legacy 1998 1998 Service Manual MECHANICAL COMPONENTS SECTION STEERING SYSTEM MSA5TCD98L21101
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download MSA5TCD98L21101 documenatation <<
Text preview - extract from the document
4-3 [W5A0] SERVICE PROCEDURE
5. Control Valve (Power Steering Gearbox) [LHD model]
5. Control Valve (Power Steering Gearbox) [LHD model]
A: CHECKING OIL LEAKING POINTS
B4M1132A
(1) Power cylinder (6) Torsion bar (11) Pipe A
(2) Cylinder (7) Valve housing (12) Pinion
(3) Rack piston (8) Valve body (13) Pinion axle
(4) Rack axle (9) Control valve
(5) Input shaft (10) Pipe B
1. OIL LEAKING POINTS sembly work, accidental damage as well as inevi-
table damage to some related parts must be taken
1) If leak point is other than a, b, c, or d, perform
into account, and spare parts for them must also
check step 5) in "OIL LEAK CHECK PROCEDURE
be prepared. However, it is essential to pinpoint the
AND REPLACEMENT PARTS" before dismounting
cause of trouble, and limit the number of replace-
gearbox from vehicle. If
ment parts as much as possible.
gearbox is dismounted without confirming where
the leak is, it must be mounted again to locate the 1) Leakage from "a"
leak point. The oil seal is damaged. Replace valve assembly
2) Even if the location of the leak can be easily with a new one.
found by observing the leaking condition, it is nec- 2) Leakage from "b"
essary to thoroughly remove the oil from the sus- The torsion bar O-ring is damaged. Replace valve
pected portion and turn the steering wheel from assembly with a new one.
lock to lock about 30 to 40 times with engine 3) Leakage from "c"
running, then make comparison of the suspected The oil seal is damaged. Replace valve assembly
portion between immediately after and several with a new one.
hours after this operation. 4) Leakage from "d"
3) Before starting oil leak repair work, be sure to The pipe is damaged. Replace the faulty pipe or
clean the gearbox, hoses, pipes, and surrounding O-ring.
parts. After completing repair work, clean these 5) If leak is other than a, b, c, or d, and if oil is
areas again. leaking from the gearbox, move the right and left
boots toward tie-rod end side, respectively, with the
2. OIL LEAK CHECK PROCEDURE AND gearbox mounted to the vehicle, and remove oil
REPLACEMENT PARTS from the surrounding portions. Then, turn the steer-
NOTE: ing wheel from lock to lock 30 to 40 times with the
Parts requiring replacement are described in the engine running, then make comparison of the
smallest unit of spare parts including damaged leaked portion immediately after and several hours
parts and spare parts damaged. In actual disas- after this operation.
36
SERVICE PROCEDURE [W5B2] 4-3
5. Control Valve (Power Steering Gearbox) [LHD model]
6) Leakage from "e" 2) Carefully draw out input shaft and remove valve
The cylinder seal is damaged. Replace rack bush assembly.
with a new one.
7) Leakage from "f"
There are two possible causes. Take following step
first. Remove the pipe assembly B from the valve
housing, and close the circuit with ST.
ST 926420000 PLUG
Turn the steering wheel from lock to lock 30 to 40
times with the engine running, then make compari-
son of the leaked portion between immediately
after and several hours after this operation.
G4M0138
CAUTION:
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo