Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 1995-1999 Approved Subaru Legacy 1998 1998 Service Manual MECHANICAL COMPONENTS SECTION WHEELS AND AXLES MSA5TCD98L21081
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download MSA5TCD98L21081 documenatation <<
Text preview - extract from the document
SERVICE PROCEDURE [W3A1] 4-2
3. Rear Axle (FWD Model)
3. Rear Axle (FWD Model) 8) Remove disc rotor from hub.
If disc rotor seizes up within hub, drive it out by
A: REMOVAL installing an 8-mm bolt in bolt hole on disc rotor.
1. DISC BRAKE
1) Disconnect ground cable from battery.
2) Jack-up vehicle, and remove rear wheel cap
and wheels.
CAUTION:
Be sure to loosen and retighten axle nut after
removing wheel from vehicle. Failure to follow
this rule may damage wheel bearings.
3) Pry hub cap off with a screwdriver placed G4M0269
between it and hub.
4) Unlock axle nut. 9) Disconnect end of parking brake cable.
5) Remove axle nut using a socket wrench. 10) Remove bolts which secure trailing link
Remove washer. assembly to rear spindle.
CAUTION: CAUTION:
Do not re-use old axle nut. Replace with a new Discard old self-locking nut. Replace with a
one. new one.
NOTE:
Temporarily tighten axle nut to hold hub in place.
6) Return parking brake lever and loosen adjust-
ing nut.
G4M0273
11) Remove bolts which secure lateral link assem-
bly to rear spindle.
CAUTION:
B4M0050A Discard old self-locking nut. Replace with a
7) Remove disc brake assembly from back plate. new one.
Suspend disc brake assembly from strut using a
wire.
G4M0272
G4M0268
23
4-2 [W3A2] SERVICE PROCEDURE
3. Rear Axle (FWD Model)
12) Remove bolts which secure strut assembly to 8) If it is difficult to remove brake drum, remove
rear spindle. adjusting hole cover from back plate, and then turn
Remove rear spindle, back plate and hub as a unit. adjusting screw using a slot-type screwdriver until
brake shoe separates from the drum.
G4M0249
G4M0242
2. DRUM BRAKE
NOTE:
1) Disconnect ground cable from battery. If brake drum seizes up within hub, drive it out by
2) Jack-up vehicle, and remove rear wheel cap installing an 8-mm bolt in bolt hole on brake drum.
and wheels.
CAUTION:
Be sure to loosen and retighten axle nut after
removing wheel from vehicle. Failure to follow
this rule may damage wheel bearings.
3) Pry hub cap off with a screwdriver placed
between it and hub.
4) Unlock axle nut.
5) Remove axle nut using a socket wrench.
Remove washer.
G4M0271
CAUTION:
Do not re-use old axle nut. Replace with a new 9) Disconnect end of parking brake cable.
one. 10) Using a flare-nut wrench, disconnect brake
pipe from wheel cylinder.
NOTE:
Temporarily tighten axle nut to hold hub in place. CAUTION:
Cover brake pipe connection to prevent entry
6) Return parking brake lever and loosen adjust- of foreign particles.
ing nut.
11) Remove bolts which secure trailing link
assembly to rear spindle.
CAUTION:
Discard old self-locking nut. Replace with a
new one.
B4M0050A
7) Remove brake drum from hub.
G4M0273
24
SERVICE PROCEDURE [W3C0] 4-2
3. Rear Axle (FWD Model)
12) Remove bolts which secure lateral link assem- 2) Remove back plate from rear spindle.
bly to rear spindle.
CAUTION:
Discard old self-locking nut. Replace with a
new one.
G4M0276
3) Using ST, press hub bolts out.
CAUTION:
G4M0272
Do not hammer hub bolt since this may deform
hub.
13) Remove bolts which secure strut assembly to ST 927080000 HUB STAND
rear spindle.
Remove rear spindle, back plate and hub as a unit.
G4M0277
G4M0249
C: INSPECTION
B: DISASSEMBLY Clean the removed parts and check them for wear,
damage and corrosion. If faulty, replace.
1) Remove hub from rear spindle.
CAUTION:
Hub unit cannot be disassembled. If faulty,
replace it as a unit.
G4M0275
25
4-2 [W3D0] SERVICE PROCEDURE
3. Rear Axle (FWD Model)
D: ASSEMBLY CAUTION:
Use a new self-locking nut.
1) Using ST, press new hub bolts into place.
2) Connect rear spindle assembly to lateral link
NOTE: assembly.
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo