Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Subaru Legacy 2000-2003 Approved Subaru Legacy 2000 2000 Service Manual TRANSMISSION AND DIFFERENTIAL SECTION Automatic Transmission and Differential MSA5TCD00L18825
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download MSA5TCD00L18825 documenatation <<
Text preview - extract from the document
SERVICE PROCEDURE [W21A0] 3-2
21. Transfer Clutch
4) Measurement of backlash (Selection of washer) 21. Transfer Clutch
Measure the gear backlash with ST1 and ST2, and
insert ST2 through the access window of the case. A: DISASSEMBLY
ST1 498247001 MAGNET BASE
ST2 498247100 DIAL GAUGE 1) Remove the seal ring.
NOTE: CAUTION:
Measure the backlash by applying a pinion tooth Be careful not to damage the seal ring.
between two bevel gear teeth.
Standard value:
0.13 -- 0.18 mm (0.0051 -- 0.0071 in)
G3M0493
2) Using a press and ST, remove the ball bearing.
CAUTION:
G3M0491
Do not reuse the bearing.
5) Using ST, install taper roller bearing. ST 498077600 REMOVER
ST 398487700 DRIFT
G3M0494
G3M0492
3) Remove the snap ring, and take out the pres-
sure plate, drive plates, and driven plates.
G3M0495
103
3-2 [W21B0] SERVICE PROCEDURE
21. Transfer Clutch
4) Remove the snap ring with ST1, ST2 and ST3, 2) Install return spring to transfer piston.
and take out the return spring and transfer clutch
piston seal.
ST1 399893600 PLIERS
ST2 398673600 COMPRESSOR
ST3 398623600 SEAT
B3M1177A
3) Install transfer clutch piston seal.
B3M1415A
5) Apply compressed air to the rear drive shaft to
remove the piston.
B3M1401A
4) Install ST to rear drive shaft.
ST 499257300 SNAP RING OUTER GUIDE
G3M0497
B: INSPECTION
1) Check the drive plate facing for wear and dam-
age.
2) Check the snap ring for wear, return spring for
permanent set and breakage, and return spring for
B3M1402A
deformation.
3) Check the lathe cut ring for damage. 5) Install snap ring to ST.
ST 499257300 SNAP RING OUTER GUIDE
C: ASSEMBLY
1) Install the transfer clutch piston.
B3M1180A
B3M1400A
104
SERVICE PROCEDURE [W21C0] 3-2
21. Transfer Clutch
6) Using ST1 and ST2, install snap ring to rear 9) Check the clearance.
drive shaft. NOTE:
NOTE: Before measuring clearance, place the same thick-
After installing snap ring, remove ST1 and ST2. ness of shim on both sides to prevent pressure
ST1 499257300 SNAP RING OUTER GUIDE plate from tilting.
ST2 499247400 INSTALLER If the clearance is not within the specified range,
select a proper pressure plate.
Standard value:
0.2 -- 0.6 mm (0.008 -- 0.024 in)
Allowable limit:
1.6 mm (0.063 in)
B3M1181A
7) Install the driven plates, drive plates, pressure
plate and snap ring.
G3M0503
Available pressure plates
Part No. Thickness mm (in)
31593AA151 3.3 (0.130)
31593AA161 3.7 (0.146)
31593AA171 4.1 (0.161)
31593AA181 4.5 (0.177)
B3M1182A
10) Press-fit the ball bearing with ST.
8) Apply compressed air to see if the assembled ST 899580100 INSTALLER
parts move smoothly.
G3M0505
G3M0502
105
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo