
DI-578
DIAGNOSTICS - AIR CONDITIONING SYSTEM
DI5CD-01
PRE-CHECK
1. LIST OF OPERATION METHODS
By operating each of the A/C control switches as shown in the diagram below, it is possible to enter the diag-
nosis check mode.
Turn ignition switch ON with AUTO and
R/F switches held down.
If both AUTO switch and R/F switch
are not pressed at the same time.
Indicator Check
R/F
OFF DTC Check OFF
(Sensor Check) AUTO Actuator Check
(continuous operation) (continuous operation)
DEF DEF
R/F R/F
DTC Check OFF
OFF Actuator Check
(Sensor Check) AUTO AUTO
(stepped operation) (stepped operation)
DEF DEF
Cancel check mode and can start
A/C control
: Indicates a switch operation.
2002 4RUNNER (RM887U)
Author : Date : 754
DI-579
DIAGNOSTICS - AIR CONDITIONING SYSTEM
2. INDICATOR CHECK
R/F Switch (a) Turn the ignition switch to ON while pressing the air condi-
tioning control AUTO switch and R/F switch simulta-
neously.
AUTO Switch
I09224
Blinking Pattern (b) Check that all the indicators light up and go off at 1 second
intervals 4 times in succession.
4 times
HINT:
1 sec.
1 sec. S After the indicator check is ended, the system enters the
DTC begins automatically.
ON
S Press the OFF switch when desiring to cancel the check
mode.
OFF
I00339
3. DTC CHECK (SENSOR CHECK)
Code Display (a) Perform an indicator check. After the indicator check is
completed, the system enters the DTC check mode auto-
matically.
(b) Read the code displayed on the panel. Refer to the list of
DTCs on page DI-582 when reading the DTCs. (DTCs
are output at the temperature display).
I09224
(c) If the slower display is desired, press the front DEF switch
Front DEF Switch
and change it to stepped operation. Each time the front
DEF switch is pressed, the display changes by 1 step.
I09224
2002 4RUNNER (RM887U)
Author : Date : 755
DI-580
DIAGNOSTICS - AIR CONDITIONING SYSTEM
No. 1 J/B 4. CLEARING DTC
(a) Pull out the ECU-B fuse in No. 1 J/B for 10 sec., or longer
to clear the DTC memory.
ECU-B Fuse (b) After reinserting the fuse, check that the normal code is
output.
I09233
2002 4RUNNER (RM887U)
Author : Date : 756
DI-581
DIAGNOSTICS - AIR CONDITIONING SYSTEM
5. ACTUATOR CHECK
R/F Switch Front DEF Switch (a) After entering the DTC check mode (Sensor Check
Mode) press the R/F switch.
(b) Since each damper, motor and relay automatically oper-
ates at 1 second intervals beginning in order from 10 in
the temperature display, check the temperature and air
flow visually and by hand.
OFF Switch If a slower display is desired, press the FRONT DEF
I09224 switch and change it to a stepped operation. Each time
the FRONT DEF switch is pressed, the display changes
by 1 step.
HINT:
S Code are displayed in order from the smaller to the larger
numbers.
S To cancel the check mode, press the Off switch.
Display Conditions
Step No.
code Blower motor Air flow vent Air inlet damper Magnetic clutch Air mix damper
FACE OFF Cool side
1 0 OFF FRESH
(0 % open)
FACE FRESH Cool side
2 1 1 OFF
(0 % open)
FRESH ON Cool side
3 2 16 FACE
(0 % open)
Cool side
4 3 16 FACE FRS/REC ON
(0 % open)
Cool / Hot
5 4 16 FACE RECIRC ON (50 % open)
Cool / Hot
6 5 16 BI-LEVEL RECIRC ON
(50 % open)
Hot side
7 6 16 FOOT RECIRC ON
(100 % open)
Hot side
8 7 16 FOOT RECIRC ON
(100 % open)
RECIRC Hot side
9 8 16 FOOT/DEF ON
(100 % open)
10 31 DEF RECIRC ON Hot side
9
(100 % open)
2002 4RUNNER (RM887U)
Author : Date : 757