Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota 4Runner 1996-2003 Approved SIL techinfo.toyota.com ileaf 02toyrm 02toypdf 02rmsour 2002 024runne pr spibea repl
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download repl documenatation <<
Text preview - extract from the document
PR-12
PROPELLER SHAFT - SPIDER BEARING
Matchmarks
SPIDER BEARING
Matchmarks PR01D-02
REPLACEMENT
1. REMOVE PROPELLER SHAFT
2WD: (See page PR-4 )
4WD: (See page PR-8 )
2. PLACE MATCHMARKS ON SHAFT AND YOKE
Z04244
3. REMOVE SNAP RINGS
(a) Using a brass bar and hammer, slightly tap in the bearing
outer races.
(b) Using 2 screwdrivers, remove the 4 snap rings from the
grooves.
Z04245
4. REMOVE SPIDER BEARINGS
NOTICE:
Be careful not to grip the propeller shaft tube too tightly in
SST a vise as this will cause deformation.
(a) Using SST, push out the bearing from the propeller shaft.
A
SST 09332-25010
HINT:
Sufficiently raise the part indicated by "A" so that it does not
PR0019 come into contact with the bearing.
(b) Clamp the bearing outer race in a vise and tap off the pro-
peller shaft with a hammer.
HINT:
Remove the bearing on opposite side in the same procedure.
(c) Install the 2 removed bearing outer races to the spider.
(d) Using SST, push out the bearing from the yoke.
SST 09332-25010
SST (e) Clamp the outer bearing race in a vise and tap off the yoke
with a hammer.
HINT:
Remove the bearing on the opposite side in the same proce-
dure.
Z04246
2002 4RUNNER (RM887U)
Author : Date : 1167
PR-13
PROPELLER SHAFT - SPIDER BEARING
Color 5. SELECT SPIDER BEARING
Select the bearing according to whether or not there is a drill
Drill Mark mark on the yoke section.
Yoke Bearing
Yoke
With drill mark With color mark (Red)
No drill mark No color mark
Drill Mark
Bearing
Cup
Z04247
6. INSTALL SPIDER BEARINGS
(a) Apply MP grease to a new spider and bearings.
NOTICE:
Be careful not to apply too much grease.
(b) Align the matchmarks on the yoke and shaft.
Z04248
(c) Fit the spider into the yoke.
SST
(d) Using SST, install new bearings on the spider.
SST 09332-25010
PR0027
(e) Using SST, adjust both bearings so that the snap ring
grooves are at maximum and equal widths.
PR0028
2002 4RUNNER (RM887U)
Author : Date : 1168
PR-14
PROPELLER SHAFT - SPIDER BEARING
7. INSTALL SNAP RINGS
(a) Install 2 new snap rings of equal thickness which will allow
0 - 0.05 mm (0 - 0.0020 in.) axial play.
HINT:
Do not reuse the snap rings.
Color or Mark Thickness mm (in.)
1 2.100 - 2.150 (0.0827 - 0.0846)
2 2.150 - 2.200 (0.0846 - 0.0866)
Q08991
3 2.200 - 2.250 (0.0866 - 0.0886)
Brown 2.250 - 2.300 (0.0886 - 0.0906)
Blue 2.300 - 2.350 (0.0906 - 0.0925)
6 2.350 - 2.400 (0.0925 - 0.0945)
7 2.400 - 2.450 (0.0945 - 0.0965)
8 2.450 - 2.500 (0.0965 - 0.0984)
(b) Using a hammer, tap the yoke until there is no clearance
between the bearing outer race and snap ring.
8. CHECK SPIDER BEARING
(a) Check that the spider bearing moves smoothly.
(b) Check the spider bearing axial play.
Bearing axial play: Maximum 0.05 mm (0.0020 in.)
HINT:
S Install new spider bearings on the shaft side in the proce-
dure described above.
S When replacing the propeller shaft spider on 4WD ve-
PR0031 hicles, be sure that the grease fitting assembly hole is fac-
ing in the direction shown in the illustrations.
2002 4RUNNER (RM887U)
Author : Date : 1169
PR-15
PROPELLER SHAFT - SPIDER BEARING
SPIDER GREASE FITTING ASSEMBLY
DIRECTION FOR FRONT PROPELLER SHAFT
No.3
The figure at left shows the
No.2 locations of the grease fittings
as seen from the rear.
No.1 No.3
No.1
No.2
SPIDER GREASE FITTING ASSEMBLY
DIRECTION FOR REAR PROPELLER SHAFT
No.1 No.2 No.3 No.5
The figure at left shows the
No.4 locations of the grease fittings
as seen from the rear.
No.1 No.2
No.4
No.3 No.5
F08178
2002 4RUNNER (RM887U)
Author : Date : 1170
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo