Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Camry 1994.2002-2007 Approved Toyota Camry 2007 Hybrid 49 07camhvo 04
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download 04 documenatation <<
Text preview - extract from the document
'07Camry hybrid_U (L/O 0610)
SECTION 4
IN CASE OF AN EMERGENCY
In case of an emergency
If your vehicle will not start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
If your hybrid system stalls while driving . . . . . . . . . . . . . . . . . . . . . . . 317
If your vehicle overheats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
If you have a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
If your vehicle becomes stuck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
If your vehicle needs to be towed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
If you cannot shift transmission selector lever . . . . . . . . . . . . . . . . . . 329
If you lose your keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
312
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
If your vehicle will not start--
(a) Simple checks (b) Emergency start
Before making these checks, make sure If the instrument cluster displays with When the hybrid system cannot be
you have sufficient fuel and that you have normal brightness levels with the started, the following procedure can be
followed the correct starting procedure giv- "POWER" switch set at ON... used if the hybrid system and "POWER"
en in "How to start the hybrid system" on You may try emergency start. See "(b) switch function normally.
page 301 in Section 3. If your vehicle is Emergency start" for further instructions. 1. Put the transmission in "P".
equipped with the engine immobilizer sys-
tem, also check whether the other keys If the instrument cluster dims or the 2. Set the mode to ACC by pushing the
will start the hybrid system. If they work, instrument cluster display turns off "POWER" switch once.
your key may be broken. Have the key with the "POWER" switch set at ON... 3. Push and hold the "POWER" switch for
checked at your Toyota dealer. If none of 1. Check that the 12 volt battery terminals about 15 seconds while depressing the
your keys work, there may be a malfunc- are tight and clean. brake pedal firmly.
tion in the immobilizer system. Call your 2. If the 12 volt battery terminals are Even if the hybrid system can be started
Toyota dealer. (See "Keys" on page 22 in O.K., the 12 volt battery is discharged. using the above procedure, the system
Section 1-2.) You may try jump starting. See "(c) may be malfunctioning. Have the vehicle
Jump starting" that follows for further checked by your Toyota dealer.
instructions. If the hybrid system cannot be started
using the above procedure, immediately
NOTICE
contact your Toyota dealer.
Hybrid vehicles cannot be push-
started. CAUTION
Do not place any objects close to the
"POWER" switch. If the object pushes
on the switch, the hybrid system may
be started unexpectedly.
313
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
(c) Jump starting
If the 12 volt battery is discharged, the
hybrid system can be started by jump D If you should accidentally get acid
starting. Depending on the vehicle con- on yourself or in your eyes, remove
dition, however, the hybrid system may any contaminated clothing and flush
not start. the affected area with water im-
mediately. Then get immediate medi-
To avoid serious injury and damage to
cal attention. If possible, continue
your vehicle which might result from an to apply water with a sponge or
explosion of the battery, acid burns,
cloth while en route to the medical
electrical burns, or damaged electronic
office.
components, follow instructions careful-
ly. D The gas normally produced by a
battery will explode if a flame or
If you are unsure about how to follow this spark is brought near. Use only
procedure, we strongly recommend that standardized jumper cables and do
you seek the help of a competent me-
not smoke or light a match while 12 VOLT BATTERY LOCATION
chanic or towing service. jump starting. The 12 volt battery is located in the right-
CAUTION hand side of the trunk. Remove the cover
to access the battery.
NOTICE
D Batteries contain sulfuric acid
which is poisonous and corrosive. The battery used for boosting must
Wear protective safety glasses when be 12 V. Do not jump start unless you
jump starting, and avoid spilling are sure that the booster battery is
acid on your skin, clothing, or ve- correct.
hicle.
314
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
JUMP STARTING PROCEDURE
Discharged battery Jumper cable
1. If the booster battery is installed in
another vehicle, make sure the vehicles
are not touching. Turn off all unneces-
sary lights and accessories.
Booster
When boosting, use the battery of battery
matching or higher quality. Any other
battery may be difficult to jump start
with. Positive
terminal
If jump starting is difficult, charge the ("+" mark) Booster
battery for several minutes. Positive terminal Discharged battery battery
Jumper cable ("+"mark)
2. If required, remove all the vent plugs Negative terminal ("-"mark)
from the booster battery. Lay a cloth
over the open vents on the battery. 4. Make the cable connections in the or- c. Connect the clamp of the negative
(This helps reduce the explosion haz- der a, b, c, d. (black) jumper cable to the negative (-)
ard, personal injuries and burns.) a. Connect the clamp of the positive terminal on the booster battery.
3. If the engine in the vehicle with the (red) jumper cable to the positive (+) d. Connect the clamp at the other end
booster battery is not running, start it terminal of the discharged 12 volt bat- of the negative (black) jumper cable to
and let it run for a few minutes. During tery. a solid, stationary, unpainted, metallic
jump starting, run the engine at about b. Connect the clamp at the other end point of the vehicle with the discharged
2000 rpm with the accelerator pedal of the positive (red) jumper cable to battery.
lightly depressed. the positive (+) terminal of the booster
battery.
315
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
5. Start the hybrid system. Make sure the If the first start attempt is not success-
"READY" light is on. ful...
If the "READY" light will not come on Check that the clamp on the jumper
and the hybrid system will not start cables are tight. Recharge the discharged
after you recharge the battery, perform battery with the jumper cables connected
the following procedure. Turn the hybrid for several minutes and restart the hybrid
system off. Open and close the driver's system in the normal way.
door. Then push the "POWER" switch If the another attempt is not successful,
briefly and firmly. the battery may be depleted. Have it ch-
If the the message "LOW T. BATTERY ecked at your Toyota dealer.
STOP THE VEHICLE SHIFT TO P" ap-
pears on the multi-information display,
the hybrid battery is also discharged.
In this condition, the hybrid system
The recommended connecting point
may not start. Contact your Toyota
is in the above illustration.
dealer.
6. Carefully disconnect the cables in the
CAUTION
exact reverse order: the negative cable
and then the positive cable.
When making the connections, to
avoid serious injury, do not lean over 7. Carefully dispose of the battery cover
the battery or accidentally let the cloths--they may now contain sulfuric
jumper cables or clamps touch any- acid.
thing except the correct battery termi- 8. If removed, replace all the battery vent
nals or the ground. plugs.
If the cause of the 12 volt battery dis-
charging is not apparent (for example,
lights left on), have the battery checked
by your Toyota dealer.
316
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
If your hybrid system stalls
while driving If your vehicle overheats
If your hybrid system stalls while driving... Any of the following may indicate that
the hybrid system has overheated: CAUTION
1. Reduce your speed gradually, keeping
a straight line. Move cautiously off the D The engine coolant temperature
To help avoid personal injury, keep
road to a safe place. gauge indicates overheating.
the hood closed until there is no
2. Turn on your emergency flashers. D The message "WATER TEMP" or steam. Escaping steam or coolant is
3. Set the "POWER" switch at ACC or off, "HYBRID SYSTEM OVER HEAT" ap- a sign of very high pressure.
and try starting the hybrid system pears on the multi-information dis-
again. play.
3. Look for obvious coolant leaks from the
If the hybrid system will not start, see "If D A loss of power is experienced. radiator, hoses, and under the vehicle.
your vehicle will not start" on page 313 in D A loud knocking or pinging noise is However, note that water draining from
this Section. heard. the air conditioning is normal if it has
been used.
If the hybrid system overheats, follow
CAUTION the procedures below:
CAUTION
D If the hybrid system is not operat- 1. Pull safely off the road, stop the ve-
hicle and turn on your emergency When the hybrid system is on, keep
ing, the power assist for the brakes
and steering will not work so steer- flashers. Put the transmission in "P" hands and clothing away from the
ing and braking will be much hard- and apply the parking brake. Turn off moving fan.
the air conditioning if it is being used.
er than usual.
D If the hybrid system stalls while 2. If coolant or steam is boiling out of the 4. If the coolant is leaking, stop the hy-
driving, do not open the driver's radiator or reservoir, stop the hybrid brid system immediately. Call a Toyota
door until the vehicle comes to a system. Wait until the steam subsides dealer for assistance.
complete stop. Opening the driver's before opening the hood. If there is no
coolant boiling over or steam, leave the 5. If there are no obvious leaks, check
door locks the steering wheel, re- the coolant reservoir. If it is dry, add
sulting in loss of steering control. hybrid system turned on and make
sure the electric cooling fan is operat- coolant to the reservoir while the hy-
ing. If it is not, turn the hybrid system brid system is on. Fill it about half full.
off. For the coolant type, see "Coolant type
selection" on page 357 in Section 7-2.
317
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
If you have a flat tire--
1. Reduce your speed gradually,
CAUTION keeping a straight line. Move cau- CAUTION
tiously off the road to a safe place
Do not attempt to remove the radiator When jacking, be sure to observe
cap when the hybrid system and ra-
well away from the traffic. Avoid
stopping on the center divider of the following to reduce the possi-
diator are hot. Serious injury could bility of death or serious injury:
result from scalding hot fluid and a highway. Park on a level spot
steam blown out under pressure. with firm ground. D Follow jacking instructions.
2. Stop the hybrid system and turn D Do not put any part of your
6. After the coolant temperature has on your emergency flashers. body under the vehicle sup-
cooled to normal, again check the cool- 3. Firmly set the parking brake and ported by the jack. Otherwise,
ant level in the reservoir. If necessary, personal injury may occur.
put the transmission in "P".
bring it up to half full again. Serious
coolant loss indicates a leak in the 4. Have everyone get out of the ve- D Do not start the hybrid system
system. You should have it checked as hicle on the side away from traffic. while your vehicle is supported
soon as possible at your Toyota dealer. by the jack.
5. Read the following instructions
thoroughly. D Stop the vehicle on a level firm
ground, firmly set the parking
brake and put the transmission
in "P". Block the wheel diago-
nally opposite to the one being
changed if necessary.
318
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
D Make sure to set the jack prop- NOTICE
erly in the jack point. Raising Do not continue driving with a
the vehicle with jack improper- deflated tire. Driving even a
ly positioned will damage the short distance can damage a
vehicle or may allow the ve- tire and wheel beyond repair.
hicle to fall off the jack and
cause personal injury.
D Never get under the vehicle
when the vehicle is supported
by the jack alone.
D Use the jack only for lifting
your vehicle during wheel
changing. Compact spare tire
D Do not raise the vehicle with The compact spare tire is designed
someone in the vehicle. for temporary emergency use only.
D When raising the vehicle, do The compact spare tire is identified
not place any objects on top by the distinctive wording
of or underneath the jack. "TEMPORARY USE ONLY" molded
into the side wall of the tire.
D Raise the vehicle only high
enough to remove and change The compact spare tire saves space
the tire. in your luggage compartment, and its
lighter weight helps to improve fuel
economy and permits easier installa-
tion in case of a flat tire.
319
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
--Required tools and spare
tire
The compact spare tire can be used
many times, if necessary. It has tread D Replace the compact spare tire
life of up to 4800 km (3000 miles) de- with the standard tire as soon
pending on road conditions and your as possible.
driving habits. When tread wear indi- D Avoid sudden acceleration,
cators appear on the tire, replace the sudden deceleration and sharp
tire. turns with the compact spare
See also the tire information on page tire.
362 in Section 7-2 for details on the
tread wear indicators and other ser- NOTICE
vice information.
Your ground clearance is re-
CAUTION duced when the compact spare
tire is installed so avoid driving 1. Get the required tools and
D The compact spare tire was de- over obstacles and drive slowly spare tire.
signed especially for your Toy- on rough, unpaved roads and 1. Jack handle
ota. Do not use it on any other speed bumps. Also, do not at- 2. Wheel nut wrench
vehicle. tempt to go through an auto- 3. Transport eyelet
D Do not use more than one com- matic car wash as the vehicle (on some models)
pact spare tire at the same may get caught, resulting in 4.
time. damage. Jack
5.
D The pressure for the compact
Spare tire
spare tire must be 420 kPa (4.2
kgf/cm2 or bar, 60 psi). To prepare yourself for an emergency,
you should familiarize yourself with
D Do not exceed 80 km/h (50
the use of the jack, each of the tools
mph) when driving with the
and their storage locations.
compact spare tire.
320
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
When storing the spare tire, put it in
place with the outer side of the wheel
facing up. Then secure the tire by re-
peating the above removal steps in
reverse order to prevent it from flying
forward during a collision or sudden
braking.
To remove the spare tire: Before removing the jack, unhook the
1. Loosen the nut and remove it. tightening strap.
2. Remove the spare tire cover. After storing the jack, make sure it is
securely held by the tightening strap.
3. Loosen the bolt and remove it.
This prevents the jack from flying for-
4. Remove the jack tray. ward during a collision or sudden
Then take the spare tire out of the stop.
vehicle.
321
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
--Blocking the wheel --Loosening wheel nuts
CAUTION
Never use oil or grease on the
bolts or nuts. The nuts may be-
come loose and the wheels may
fall off, which could cause a seri-
ous accident.
2. Block the wheel diagonally op- 3. Loosen all the wheel nuts.
posite the flat tire to keep the Always loosen the wheel nuts before
vehicle from rolling when it is raising the vehicle.
jacked up.
Turn the wheel nuts counterclockwise
When blocking the wheel, place a to loosen. To get maximum leverage,
wheel block or equivalent in front of fit the wrench to the nut so that the
one of the front wheels or behind one handle is on the right side, as shown
of the rear wheels. above. Grab the wrench near the end
of the handle and pull up on the han-
dle. Be careful that the wrench does
not slip off the nut.
Do not remove the nuts yet--just un-
screw them about one-half turn.
322
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
--Positioning the jack --Raising your vehicle
Jack point guide
4. Position the jack at the correct The jack point guides are located un- 5. After making sure that no one
jack point as shown. der the rocker panel. They indicate is in the vehicle, raise it high
Make sure the jack is positioned on the jack point positions. enough so that the spare tire
a level and solid place. can be installed.
Remember you will need more ground
clearance when putting on the spare
tire than when removing the flat tire.
To raise the vehicle, insert the jack
handle into the jack (it is a loose fit)
and turn it clockwise. As the jack
touches the vehicle and begins to lift,
double-check that it is properly posi-
tioned.
323
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
--Changing wheels
CAUTION
Never get under the vehicle when
the vehicle is supported by the
jack alone.
6. Remove the wheel nuts and Before putting on wheels, remove any
change tires. corrosion on the mounting surfaces
Lift the flat tire straight off and put it with a wire brush or such. Installation
aside. of wheels without good metal-to-met-
al contact at the mounting surface can
Roll the spare wheel into position and cause wheel nuts to loosen and
align the holes in the wheel with the eventually cause a wheel to come off
bolts. Then lift up the wheel and get while driving.
at least the top bolt started through
its hole. Wiggle the tire and press it
back over the other bolts.
324
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
--Reinstalling wheel nuts --Lowering your vehicle
CAUTION
Never use oil or grease on the
bolts or nuts. Doing so may lead
to overtightening the nuts and
damaging the bolts. The nuts
may loose and the wheels may
fall off, which could cause a seri-
ous accident. If there is oil or
grease on any bolt or nut, clean
it.
7. Reinstall all the wheel nuts fin- 8. Lower the vehicle completely
ger tight. and tighten the wheel nuts.
Reinstall the wheel nuts (tapered end Turn the jack handle counterclock-
inward) and tighten them as much as wise to lower the vehicle.
you can by hand. Press back on the Use only the wheel nut wrench to
tire and see if you can tighten them tighten the nuts. Do not use other
more. tools or any additional leverage other
than your hands, such as a hammer,
pipe or your foot. Make sure the
wrench is securely engaged over the
nut.
Tighten each nut a little at a time in
the order shown. Repeat the process
until all the nuts are tight.
325
2007 CAMRY HV from Aug. '06 Prod. (OM33727U)
'07Camry hybrid_U (L/O 0610)
--After changing wheels
9. Check the air pressure of the re- Initial adjustment of the tire pres-
CAUTION placed tire. sure warning system is necessary
Adjust the air pressure to the specifi- after you have replaced your tires
D When lowering the vehicle, or wheels. See "Tire pressure
make sure all portions of your cation designed on page 385 in Sec-
tion 8. If the pressure is lower, drive warning system" on page 168 in
body and all other persons Section 1-7.
around will not be injured as slowly to the nearest service station
the vehicle is lowered to the and fill to the correct pressure.
CAUTION
ground. Do not forget to reinstall the tire infla-
D Have the wheel nuts tightened tion valve cap as dirt and moisture Before driving, make sure all the
with torque wrench to 103 N◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo