Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Celica 1988-1989.1993-1994.2000 Approved Toyota Celica 1989 ac compressor servicing

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.



Image preview - the first page of the document
ac compressor servicing


>> Download ac compressor servicing documenatation <<

Text preview - extract from the document
                                                       A/C COMPRESSOR SERVICING

                                                                      1988 Toyota Celica




                1988 A/C Compressor Service

                Camry, Celica, Corolla, Cressida, Land Cruiser, MR2,
                Pickup/4Runner, Supra, Van/Wagon

       * PLEASE READ THIS FIRST *
CAUTION: When discharging air conditioning system, use only approved
         refrigerant recovery/recycling equipment. Make every attempt
         to avoid discharging refrigerant into the atmosphere.

       NIPPONDENSO 10-CYLINDER

        SHAFT SEAL
NOTE:           Check compressor refrigerant oil level when replacing seals.
                See A/C COMPRESSOR COMPRESSOR OIL CHECKING article in this
                section.

         Removal
         1) Hold clutch hub stationary and remove center nut. Screw
remover into center of hub. Turn center bolt to remove pressure plate.
         2) Remove shims from shaft. Remove snap ring from inside of
pulley. Tap pulley off of shaft with plastic mallet. Be careful not to
distort pulley while removing.
         3) Disconnect clutch coil wires from compressor housing.
Remove snap ring inside coil and lift coil off compressor. Pry dust
seal out from around compressor shaft (if equipped).
         4) Place shaft key remover on shaft and turn to remove key.
Remove drain plug (if equipped). Remove bolts holding service valves
to body of compressor and remove valves. Discard "O" rings. Drain oil
out of compressor.
         5) Remove 6 through bolts from front head of compressor and
discard washers. Tap head loose from compressor, being careful not to
scratch sealing surfaces. Remove snap ring (if equipped) from front
housing. Press seal plate out. Remove seal from shaft.

         Installation
         1) Lubricate shaft seal with clean refrigerant oil. Place on
compressor shaft. Lubricate seal plate (and "O" ring, if equipped) and
install in front housing. Install snap ring (if equipped).
         2) Place front housing on compressor body. Using new washers,
install through bolts. Tighten bolts evenly and alternately to 18 ft.
lbs. (24 N.m). Install shaft key with installer and plastic mallet.
Insert dust seal into front of compressor.
         3) Install drain plug using new gasket. Add correct amount of
refrigerant oil to compressor. If service valves were removed, coat
new "O" rings with refrigerant oil and install service valves.
         4) Place clutch coil on compressor and install snap ring.
Install shims on shaft to adjust clearance between pressure plate and
rotor to .016-.028" (.41-.71 mm). Tighten shaft nut to 12 ft. lbs.
(16 N.m). See REFRIGERANT OIL & R-12 CAPACITIES table for system
capacities.

       A/C SYSTEM SPECIFICATIONS
REFRIGERANT OIL & R-12 CAPACITIES TABLE



◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo