Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Celica 1988-1989.1993-1994.2000 Approved Toyota Celica 1993 WIPER_WA
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download WIPER_WA documenatation <<
Text preview - extract from the document
WIPER/WASHER SYSTEM
1993 Toyota Celica
1993 ACCESSORIES/SAFETY EQUIPMENT
Toyota Wiper/Waher Systems
Camry, Celica, Corolla, Land Cruiser, MR2, Paseo, Pickup,
Previa, Supra, Tercel, T100, 4Runner
WARNING: Camry, Celica, Corolla, MR2, Paseo, Previa, Supra and Tercel
are equipped with a driver's side air bag. Use extreme
caution while servicing components on steering column.
Ensure ignition switch is in LOCK position and negative
battery cable is disconnected for at least one minute before
starting service. DO NOT apply electrical power to any
component on steering column without disconnecting air bag
control unit. Information labels are attached to air bag
components. Follow all notices on labels. Use only DVOM with
minimum of 10-k/ohms impedance to check ANY circuit.
DESCRIPTION & OPERATION
All models are equipped with 2-speed wiper motors. An
intermittent wiper system is optional. Front wiper motors are
protected by an internal circuit breaker. Celica, Corolla, Land
Cruiser, Previa, Supra and 4Runner are equipped with rear wipers.
TESTING
FRONT WIPER MOTOR TEST
Camry, Celica, MR2, Pickup & 4Runner
1) Using 12-volt battery, connect jumper wire from positive
battery terminal to wiper motor terminal No. 2. See Fig. 1. Connect
another jumper wire between negative battery terminal and wiper motor
body or motor ground wire location at mounting bolt hole. Motor should
operate at low speed.
2) Remove jumper wire from terminal No. 2. Reconnect jumper
wire to wiper motor terminal No. 1. Motor should operate at high
speed. Remove jumper wire from terminal No. 1 and reconnect jumper
wire to wiper motor terminal No. 2. With motor running at low speed,
stop motor at any position except PARK position by disconnecting
jumper wire from terminal No. 2. Install another jumper wire between
wiper motor terminals No. 2 and 3.
3) Ensure motor body ground is still connected to negative
battery terminal. Connect positive battery terminal jumper wire to
wiper motor terminal No. 4. Motor should start running and then stop
at PARK position. Replace motor if operation is not as described.
Fig. 1: Front Wiper Motor Terminal ID
Courtesy of Toyota Motor Sales, U.S.A., Inc.
All Other Models
1) Using 12-volt battery, connect jumper wire from positive
battery terminal to wiper motor terminal No. 3. See Fig. 1. Connect
another jumper wire between negative battery terminal and wiper motor
terminal No. 1. Motor should operate at low speed.
2) Remove jumper wire from terminal No. 3. Reconnect
positive battery terminal jumper wire to wiper motor terminal No. 2.
Motor should operate at high speed.
3) Remove jumper wire from terminal No. 2 and reconnect
jumper wire to wiper motor terminal No. 3. With motor running at low
speed, stop motor at any position except PARK position by
disconnecting jumper wire from terminal No. 3. Install another jumper
wire between wiper motor terminals No. 3 and 4 on Previa, or terminals
No. 3 and 5 on all other models.
4) Ensure motor terminal No. 1 (ground terminal) is still
connected to battery negative terminal. Connect positive battery
terminal jumper wire to wiper motor terminal No. 5 on Previa, or
terminal No. 6 on all other models. Motor should start running and
then stop at the PARK position. Replace motor if operation is not as
described.
FRONT WIPER RELAY TEST
Previa
1) Ensure wiper motor operation is correct. See FRONT WIPER
MOTOR TEST. If motor operates correctly when tested separately from
switch, check wiper switch and front wiper relay. See FRONT WIPER
SWITCH TEST. For front relay location, see Fig. 2.
2) Check front wiper relay. Using an ohmmeter, check
continuity between relay terminals No. 1 and 4. See Fig. 3. No
continuity should exist. Connect ohmmeter leads to relay terminals No.
1 and 3. Continuity should exist. If continuity is not as described,
replace relay.
Fig. 2: Locating Wiper Relays (Previa)
Courtesy of Toyota Motor Sales, U.S.A., Inc.
Fig. 3: Front & Rear Wiper Relay Terminal ID
Courtesy of Toyota Motor Sales, U.S.A., Inc.
FRONT WIPER SWITCH TEST
With wiper switch in specified position, ensure continuity
exists between terminals listed. See WIPER SWITCH CONTINUITY TEST
table. See Fig. 4. Replace wiper switch assembly if continuity is not
as specified.
WIPER SWITCH CONTINUITY TEST TABLE
◦ Jabse Service Manual Search 2024 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo