Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 1998-2003 Approved FSM 01 repins geninf
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download geninf documenatation <<
Text preview - extract from the document
IN-4
INTRODUCTION - REPAIR INSTRUCTIONS
REPAIR INSTRUCTIONS IN0CO-18
GENERAL INFORMATION
BASIC REPAIR HINT
(a) Use fender, seat and floor covers to keep the vehicle
clean and prevent damage.
(b) During disassembly, keep parts in the appropriate order
to facilitate reassembly.
FI1066
(c) Installation and removal of battery terminal:
(1) Before performing electrical work, disconnect the
negative (-) terminal cable from the battery.
(2) If it is necessary to disconnect the battery for in-
spection or repair, first disconnect the negative (-)
terminal cable.
(3) When disconnecting the terminal cable, to prevent
damage to battery terminal, loosen the cable nut
and raise the cable straight up without twisting or
prying it.
(4) Clean the battery terminals and cable ends with a
clean shop rag. Do not scrape them with a file or oth-
er abrasive objects.
(5) Install the cable ends to the battery terminals after
loosening the nut, and tighten the nut after installa-
tion. Do not use a hammer to tap the cable ends
onto the terminals.
(6) Be sure the cover for the positive (+) terminal is
properly in place.
(d) Check hose and wiring connectors to make sure that they
are connected securely and correctly.
(e) Non-reusable parts
(1) Always replace cotter pins, gaskets, O-rings, oil
seals, etc. with new ones.
(2) Non-reusable parts are indicated in the component
illustrations by the "z" symbol.
(f) Precoated parts
Precoated parts are bolts, nuts, etc. that are coated with
a seal lock adhesive at the factory.
(1) If a precoated part is retightened, loosened or
caused to move in any way, it must be recoated with
the specified adhesive.
(2) When reusing precoated parts, clean off the old
Seal Lock Adhesive adhesive and dry with compressed air. Then apply
Z11554 the specified seal lock adhesive to the bolt, nut or
threads.
2001 SIENNA (RM787U)
Author : Date : 4
IN-5
INTRODUCTION - REPAIR INSTRUCTIONS
(3) Precoated parts are indicated in the component il-
lustrations by the "L" symbol.
(g) When necessary, use a sealer on gaskets to prevent
leaks.
(h) Carefully observe all specifications for bolt tightening
torques. Always use a torque wrench.
(i) Use of special service tools (SST) and special service ma-
terials (SSM) may be required, depending on the nature
of the repair. Be sure to use SST and SSM where speci-
fied and follow the proper work procedure. A list of SST
and SSM can be found in Preparation section in this
manual.
Medium Current Fuse and High Current Fuse (j) When replacing fuses, be sure the new fuse has the cor-
Equal Amperage Rating rect amperage rating. DO NOT exceed the rating or use
one with a lower rating.
BE1367
Illustration Symbol Part Name Abbreviation
FUSE FUSE
MEDIUM CURRENT FUSE M-FUSE
HIGH CURRENT FUSE H-FUSE
FUSIBLE LINK FL
CIRCUIT BREAKER CB
V00076
2001 SIENNA (RM787U)
Author : Date : 5
IN-6
INTRODUCTION - REPAIR INSTRUCTIONS
(k) Care must be taken when jacking up and supporting the
vehicle. Be sure to lift and support the vehicle at the prop-
er locations (See page IN-8 ).
S Cancel the parking brake on the level place and
shift the transmission in Neutral (or N position).
S When jacking up the front wheels of the vehicle at
first place stoppers behind the rear wheels.
S When jacking up the rear wheels of the vehicle at
first place stoppers before the front wheels.
S When either the front or rear wheels only should be
jacked up, set rigid racks and place stoppers in front
and behind the other wheels on the ground.
S After the vehicle is jacked up, be sure to support it
on rigid racks . It is extremely dangerous to do any
work on a vehicle raised on a jack alone, even for
a small job that can be finished quickly.
(l) Observe the following precautions to avoid damage to the
following parts:
(1) To disconnect vacuum hoses, pull off the end, not
WRONG CORRECT the middle of the hose.
IN0253
(2) To pull apart electrical connectors, pull on the con-
WRONG CORRECT nector itself, not the wires.
(3) Be careful not to drop electrical components, such
as sensors or relays. If they are dropped on a hard
floor, they should be replaced and not reused.
(4) When steam cleaning an engine, protect the elec-
tronic components, air filter and emission-related
components from water.
IN0252 (5) Never use an impact wrench to remove or install
temperature switches or temperature sensors.
(6) When checking continuity at the wire connector, in-
sert the tester probe carefully to prevent terminals
from bending.
(7) When using a vacuum gauge, never force the hose
onto a connector that is too large. Use a step-down
adapter for adjustment. Once the hose has been
stretched, it may leak air.
2001 SIENNA (RM787U)
Author : Date : 6
IN-7
INTRODUCTION - REPAIR INSTRUCTIONS
Example: (m) Installation and removal of vacuum hose:
(1) When disconnecting vacuum hoses, use tags to
identify how they should be reconnected to.
(2) After completing a job, double check that the vacu-
um hoses are properly connected. A label under the
hood shows the proper layout.
(n) Unless otherwise stated, all resistance is measured at an
ambient temperature of 20◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo