Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 1998-2003 Approved FSM 15 fds reas
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download reas documenatation <<
Text preview - extract from the document
SA-20
SUSPENSION AND AXLE - FRONT DRIVE SHAFT
SA07K-02
REASSEMBLY
1. INSTALL NO.2 DUST DEFLECTOR
SST
Using SST and a press, install a new No.2 dust deflector.
SST 09309-36010, 09316-20011
W02121
2. RH DRIVE SHAFT:
ASSEMBLE INBOARD JOINT SHAFT
SST
(a) Install a new snap ring to the inboard joint shaft.
(b) Using SST and a press, install a new bearing.
SST 09223-56010
(c) Using a snap ring expander, install a new snap ring.
W03193
(d) Using SST and a press, install a new dust cover.
SST 09223-56010
SST
W03316
3. INSTALL DUST COVER
(a) LH drive shaft:
Using SST and a press, install a dust cover.
SST SST 09223-56010, 09555-55010
SST
W03145
(b) RH drive shaft:
Using SST and a press, install a new dust cover until the
SST
distance from the tip of the inboard joint shaft to the dust
cover falls within the specification, as shown in the il-
lustration.
100.5 mm SST 09223-56010
(3.957 in.)
W03194
2001 SIENNA (RM787U)
Author : Date : 1307
SA-21
SUSPENSION AND AXLE - FRONT DRIVE SHAFT
Outboard Joint Boot 4. TEMPORARILY INSTALL OUTBOARD AND INBOARD
Inboard Joint Boot
JOINT BOOTS AND NEW BOOT CLAMPS
HINT:
S Before installing the boots, wrap the spline of the drive
shaft with vinyl tape to prevent the boots from being dam-
aged.
S Before installing the boots, place 3 new clamps to the
small boot ends and large end (wheel side) and then
Vinyl Tape install boots to drive shaft.
W03195
5. INSTALL INBOARD JOINT SHAFT TO OUTBOARD
JOINT SHAFT
Align the matchmarks placed at removal, and using a snap ring
expander, put in the inboard joint shaft with expanding the snap
ring.
6. INSTALL BOOT TO OUTBOARD JOINT
Before assembling the boot, pack the outboard joint and boot
with grease in the boot kit.
Grease capacity: (Color = Black)
105 - 125 g (3.7 - 4.4 oz.)
7. INSTALL BOOT TO INBOARD JOINT SHAFT
(a) Pack the inboard joint and boot with grease in the boot kit.
Grease capacity: (Color = Gray)
Joint side: 120.0 - 130.0 g (4.2 - 4.6 oz.)
Boot side: 52.5 - 57.5 g (2.1 - 2.3 oz.)
(b) Install the boot to the inboard joint shaft.
8. ASSEMBLE BOOT CLAMPS TO BOTH BOOTS
(a) Make sure that the 2 boots are on the shaft groove.
(b) Make sure that the 2 boots are not stretched or contracted
when the drive shaft is at standard length.
Drive shaft standard length
LH 586.0 ◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo