Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 1998-2003 Approved FSM 18 saa disp
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download disp documenatation <<
Text preview - extract from the document
RS-42
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY
RS0K5-03
DISPOSAL
HINT:
When scrapping vehicles equipped with an SRS or disposing
of the side airbag assembly always first deploy the airbag in ac-
cordance with the procedure described below. If any abnormal-
ity occurs with the airbag deployment, contact the SERVICE
DEPT. of TOYOTA MOTOR SALES, U.S.A., INC.
CAUTION:
S Never dispose of a side airbag assembly which has
an undeployed airbag.
S The airbag produces a sizeable exploding sound
when it deploys, so perform the operation out-of-
doors and where it will not create a nuisance to
nearby residents.
S When deploying the airbag, always use the specified
SST (SRS Airbag Deployment Tool), perform the op-
eration in a place away from electrical noise.
SST 09082-00700
SST S When deploying an airbag, perform the operation at
least 10 m (33 ft) away from the airbag assembly.
S The side airbag assembly is very hot when the airbag
is deployed, so leave it alone for at least 30 minutes
AB0152 after deployment.
S Use gloves and safety glasses when handling side
airbag assembly with the deployed airbag.
S Always wash your hands with water after completing
the operation.
S Do not apply water, etc. to a side airbag assembly with
the deployed airbag.
1. AIRBAG DEPLOYMENT WHEN SCRAPPING VE-
HICLE
HINT:
Battery Have a battery ready as the power source to deploy the airbag.
(a) Check functioning of the SST (See step 1-(a) on page
SST RS-16 ).
SST 09082-00700
AB0158
2001 SIENNA (RM787U)
Author : Date : 1492
RS-43
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY
(b) Disconnect the side airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
H17016
(c) Install the SST.
(1) Connect the connectors of the 2 SST to the airbag
connector.
SST 09082-00700, 09082-00750
NOTICE:
To avoid damaging the SST connector and wire harness,
Battery
do not lock the secondary lock of the twin lock.
SST
H17017
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
Battery (3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
SST
terminal and the black clip to the battery negative
10 m (33 ft) or more (-) terminal.
R13455
(d) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:
S The side airbag assembly is very hot when the airbag
is deployed, so leave it alone for at least 30 minutes
H17018 after deployment.
S Use gloves and safety glasses when handling the
side airbag assembly with the deployed airbag.
S Do not apply water, etc. to the side airbag assembly
with the deployed airbag.
S Always wash your hands with water after completing
the operation.
S When scrapping a vehicle, deploy the airbag and
scrap the vehicle with the side airbag assembly still
installed.
2001 SIENNA (RM787U)
Author : Date : 1493
RS-44
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY
HINT:
The airbag deploys simultaneously as the LED of SST activa-
tion switch lights up.
2. DEPLOYMENT WHEN DISPOSING OF SIDE AIRBAG
ASSEMBLY
NOTICE:
S When disposing of the side airbag assembly only,
never use the customer's vehicle to deploy the air-
bag.
S Be sure to follow the procedure given below when de-
ploying the airbag.
HINT:
Have a battery ready as the power source to deploy the airbag.
(a) Remove the seatback assembly (See page RS-39 ).
(b) Open the fastener of the seatback cover.
(c) Remove the side airbag assembly from the seatback as-
sembly.
CAUTION:
When storing the side airbag assembly, keep the upper sur-
face of the airbag deployment side facing upward.
H17014
(d) Using a service-purpose wire harness, tie down the side
Wire Harness
airbag assembly to the tire.
Diameter Wire harness: Stripped wire harness section
1.25 mm2 or more (0.0019 in2. or more)
CAUTION:
If a wire harness which is too thin or some other thing is
used to tie down the side airbag assembly, it may be
Stripped Wire Harness Section
snapped by the shock when the airbag is deployed. This is
AB0163 highly dangerous. Always use a wire harness for vehicle
use which is at least 1.25 mm2 (0.0019 in2.).
HINT:
To calculate the square of the stripped wire harness section-
Square = 3.14 x (Diameter)2 divided by 4
2001 SIENNA (RM787U)
Author : Date : 1494
RS-45
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY
(1) Install the 2 nuts to the side airbag assembly.
H11966
(2) Wind the wire harness around the stud bolts of the
side airbag assembly as shown in the illustration.
H11967
(3) Position the side airbag assembly inside the tire
with the airbag deployment direction facing inside.
Tire size: Must exceed the following dimensions-
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)
CAUTION:
S Make sure the wire harness is tight. It is very danger-
ous when a loose wire harness results in the side air-
H11968 bag assembly coming free due to the shock from the
airbag deploying.
S Always tie down the side airbag assembly with the
airbag deployment side facing inside.
NOTICE:
The tire will be marked by the airbag deployment, so when
disposing of the airbag use a redundant tire.
(e) Check functioning of the SST (See step 1-(a) on page
RS-16 ).
SST 09082-00700
Battery
SST
AB0158
2001 SIENNA (RM787U)
Author : Date : 1495
RS-46
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY
(f) Place the tires.
(1) Place at least 2 tires under the tire to which the side
airbag assembly is tied.
(2) Place at least 2 tires over the tire to which the side
Tires
(5 or More) airbag assembly is tied. The top tire should have the
wheel installed.
H01336
(3) Tie the tires together with 2 wire harness.
CAUTION:
Make sure that the wire harness are tight. It is very danger-
ous when loose wire harness results in the tires coming
free due to the shock from the airbag deploying.
HINT:
Place the SST connector and wire harness inside tires. Secure
at least 1 m (3 ft) of slack for the wire harness.
R05403
(g) Install the SST.
Connect the connectors of the 2 SST to the side airbag
assembly connector.
Battery SST 09082-00700, 09082-00750
NOTICE:
SST Side Airbag To avoid damaging the SST connector and wire harness,
Assembly
do not lock the secondary lock of the twin lock. Also, se-
cure some slack for the SST wire harness inside the tire.
10 m (33 ft) or more (h) Deploy the airbag.
H01337
(1) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(-) terminal.
(2) Check that no one is within 10 m (33 ft) area around
the tire which the side airbag assembly is tied to.
(3) Press the SST activation switch and deploy the air-
bag.
HINT:
The airbag deploys simultaneously as the LED of the SST ac-
tivation switch lights up.
(i) Dispose of the side airbag assembly.
CAUTION:
S The side airbag assembly is very hot when the airbag
is deployed, so leave it alone for at least 30 minutes
after deployment.
S Use gloves and safety glasses when handling a side
airbag assembly with the deployed airbag.
S Do not apply water etc. to a side airbag assembly with
H00544 the deployed airbag.
2001 SIENNA (RM787U)
Author : Date : 1496
RS-47
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY
S Always wash your hands with water after completing
the operation.
(1) Remove the side airbag assembly from the tire.
(2) Place the side airbag assembly in a vinyl bag, tie the
end tightly and dispose of it in the same way as oth-
er general parts disposal.
3. DEPLOYMENT WHEN DISPOSING OF SIDE AIRBAG
ASSEMBLY WITH AIRBAG DEPLOYED IN COLLISION
Dispose of the side airbag assembly.
CAUTION:
S The side airbag assembly is very hot when the airbag
is deployed, so leave it alone for at least 30 minutes
after deployment.
S Use gloves and safety glasses when handling a side
H00544 airbag assembly with the deployed airbag.
S Do not apply water etc. to a side airbag assembly with
the deployed airbag.
S Always wash your hands with water after completing
the operation.
(1) Remove the side airbag assembly from the seat
(See page RS-39 and see step 2).
(2) Place the side airbag assembly in a vinyl bag, tie the
end tightly and dispose of it in the same way as oth-
er general parts disposal.
2001 SIENNA (RM787U)
Author : Date : 1497
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo