Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 1998-2003 Approved FSM 20 froseama repl
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download repl documenatation <<
Text preview - extract from the document
BO-128
BODY - FRONT SEAT (Manual Adjuster Type)
BO3YB-01
REPLACEMENT
HINT:
S The following is the seat heater replacement procedure.
S Care should be taken during operation to protect the seat
cover from scratches, dirt or accidental cuts.
1. REMOVE FRONT SEAT (See page BO-125 )
2. REMOVE SEATBACK COVER AND SEAT CUSHION
COVER (See page BO-126 )
3. TURN SEAT COVER INSIDE OUT
4. REMOVE SEAT WIRE
(a) Seat cushion cover:
Remove the 3 seat wires from the seat cushion cover.
(b) Seatback cover:
Remove the 2 seat wires from the seatback cover.
5. REMOVE SEAT HEATER
(a) Seat cushion cover:
Cut the 8 tack pins which are fastened to the seat heater,
then remove the seat heater.
(b) Seatback cover:
Cut the 8 tack pins which are fastened to the seat heater,
then remove the seat heater.
6. INSTALL NEW SEAT HEATER
(a) Set a new seat heater.
HINT:
Face the marked side (mark indication) to the seat cushion pad
and seatback pad.
(b) Using a tacker, attach tack pins to the seat heater as
shown in the illustration below.
Tacker: BANZAI 303XT or equivalent
NOTICE:
Do not substitute other metal part in place of tack pins.
Insufficient distance between the heater and cover may re-
sult in damage to the heater.
HINT:
S Attach tack pins on the seam side so that the wire can be
threaded through the hole from the fold side.
S Sewing thread can be substituted for tack pins.
However, allow a distance of 6 - 7 mm (0.24 - 0.28 in.)
between both sewed parts of the heater and cover.
2001 SIENNA (RM787U)
Author : Date : 1805
BO-129
BODY - FRONT SEAT (Manual Adjuster Type)
Seat cushion cover:
Front
a a
F: Tack Pin
Mark Indication
a-a
Listing Pocket
Seat Heater Seat Wire
Seat Wire Seat Heater
Tack Pin
Tack Pin
Correct Seat Heater
Seat Cushion Cover Tack Pin
Seat Wire
Incorrect
H15884
H13613
H15900
2001 SIENNA (RM787U)
Author : Date : 1806
BO-130
BODY - FRONT SEAT (Manual Adjuster Type)
Seatback cover:
a a Upper
F: Tack Pin
Mark Indication
a-a
Listing Pocket
Seat Heater Seat Wire
Seat Heater
Seat Wire
Tack Pin
Tack Pin
Correct Seat Heater
Seatback Cover Tack Pin
Seat Wire
Incorrect
H15773
H13613
H17550
2001 SIENNA (RM787U)
Author : Date : 1807
BO-131
BODY - FRONT SEAT (Manual Adjuster Type)
7. INSTALL SEAT WIRE
(a) Seat cushion cover:
Install the 3 seat wires to the seat cushion cover.
(b) Seatback cover:
Install the 2 seat wires to the seatback cover.
HINT:
Listing Pocket Pass the wire over the seat heater as shown in the illustration.
8. REVERSE SEAT COVER BACK TO ITS ORIGINAL
Wire POSITION
9. INSTALL SEATBACK COVER AND SEAT CUSHION
COVER (See page BO-132 )
10. INSTALL FRONT SEAT (See page BO-134 )
Seat Heater H13614
2001 SIENNA (RM787U)
Author : Date : 1808
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo