Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 1998-2003 Approved FSM 20 wind remo
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download remo documenatation <<
Text preview - extract from the document
BO-59
BODY - WINDSHIELD
BO240-02
REMOVAL
1. REMOVE FRONT DOOR SCUFF PLATES
2. REMOVE COWL SIDE BOARDS
3. REMOVE FRONT DOOR OPENING TRIM COVERS
: 5 Clips 4. REMOVE FRONT PILLAR GARNISH
(a) Using a screwdriver, remove the front pillar garnish.
HINT:
Tape the screwdriver tip before use.
(b) w/ Tweeter speaker:
Disconnect the connector.
(c) Employ the same manner described above to the other
side.
H02382 5. REMOVE SUN VISORS AND HOLDERS
6. REMOVE ASSIST GRIP
7. w/ Sliding roof:
REMOVE SLIDING ROOF OPENING TRIM MOULDING
8. REMOVE ROOF DRIP SIDE CHANNELS
9. REMOVE ROOF CONSOLE BOX
(a) XLE, LE Grade:
Using a screwdriver, remove the 2 lenses.
HINT:
Tape the screwdriver tip before use.
H02386
(b) CE Grade:
Using a screwdriver, remove the lens.
HINT:
Tape the screwdriver tip before use.
H02387
2001 SIENNA (RM787U)
Author : Date : 1736
BO-60
BODY - WINDSHIELD
(c) Remove the 3 screws and roof console box, then discon-
nect the connector.
10. REMOVE GLASSES BOX
Remove the 2 screws and glasses box.
11. REMOVE FRONT SIDE OF ROOF HEADLINING
(See page BO-108 )
12. REMOVE WIPER ARMS
13. REMOVE HOOD TO COWL TOP SEAL
H02388
14. REMOVE COWL TOP VENTILATOR LOUVERS
(a) Remove the clip and RH cowl top ventilator louver, then
disconnect the washer hose.
(b) Remove the clip and LH cowl top ventilator louver, then
disconnect the washer hose.
H02359
15. REMOVE OUTSIDE MOULDING
(a) Attach the rivet cutter to the drill.
(b) Gently and vertically put the drill to the rivet, and cut the
rivet flanges.
NOTICE:
S Prizing the hole with a drill can lead to damage to the
rivet hole or breaking the rivet cutter.
S Take care as the cut rivet is hot.
H02660 (c) Even if flange is taken off, continue drilling and push out
remaining fragments with the drill.
(d) Remove the outside moulding.
(e) Employ the same manner described above to the other
side.
16. REMOVE UPPER OUTSIDE MOULDING
Using a knife, cut off the moulding as shown.
NOTICE:
Do not damage the body with the knife.
H02661
2001 SIENNA (RM787U)
Author : Date : 1737
BO-61
BODY - WINDSHIELD
17. REMOVE WINDSHIELD GLASS
(a) Push piano wire through between the body and glass
from the interior.
(b) Tie both wire ends to wooden block or a similar object.
HINT:
Apply adhesive tape to the outer surface to keep the surface
from being scratched.
BO5232
NOTICE:
When separating the glass, take care not to damage the
paint and interior and exterior ornaments. To prevent
scratching the safety pad when removing the windshield,
place a plastic sheet between the piano wire and safety
pad.
(c) Cut the adhesive by pulling the piano wire around it.
(d) Remove the glass.
BO1689 NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.
2001 SIENNA (RM787U)
Author : Date : 1738
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo