Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 04 05 2011n cip0766
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download cip0766 documenatation <<
Text preview - extract from the document
05-606 DIAGNOSTICS - ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT] 05BUN-02
DTC P0766 SHIFT SOLENOID "D" PERFORMANCE
(SHIFT SOLENOID VALVE S4)
SYSTEM DESCRIPTION
The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th
or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical
problems of the shift solenoid valves and valve body.
DTC No. DTC Detecting Condition Trouble Area
S Shift solenoid valve S4 remains open or closed
S Valve body is blocked
The gear required by the ECM does not match the actual gear
P0766 S Shift solenoid valve S4
when driving (2-trip detection logic)
S Automatic transaxle (clutch, brake or gear etc.)
S ECM
MONITOR DESCRIPTION
The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". According to the input shaft
revolution, intermediate (counter) shaft revolution and output shaft revolution, the ECM detects the actual
gear position (1st, 2nd, 3rd, 4th or 5th gear position). When the gear position commanded by the ECM and
the actual gear position are not same, the ECM illuminates the MIL and stores the DTC.
MONITOR STRATEGY
P0766:
Related DTCs Shift solenoid valve S4/ON malfunction
Shift solenoid valve S4/OFF malfunction
Shift solenoid valve S4, Speed sensor (NT), Speed sensor (NC), Crankshaft posi-
Required sensors/Components
tion sensor (NE)
Frequency of operation Continuous
OFF malfunction (A) and ON malfunction (B)
1 sec.
OFF malfunction (B)
Duration
1.2 sec.
ON malfunction (A)
0.8 sec.
MIL operation 2 driving cycles
Sequence of operation None
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 789
DIAGNOSTICS - ELECTRONIC CONTROLLED AUTOMATIC 05-607
TRANSAXLE [ECT]
TYPICAL ENABLING CONDITIONS
All:
Transmission range "D"
ECT (Engine coolant temperature) 10_C (50_F) or more
TFT (Transmission fluid temperature) -20 _C (-4_F) or more
TFT sensor circuit Not circuit malfunction
ECT sensor circuit Not circuit malfunction
Turbine speed sensor circuit Not circuit malfunction
Intermediate shaft speed sensor circuit Not circuit malfunction
Output speed sensor circuit Not circuit malfunction
Shift solenoid valve SL1 circuit Not circuit malfunction
Shift solenoid valve SL2 circuit Not circuit malfunction
Shift solenoid valve SL3 circuit Not circuit malfunction
Shift solenoid valve S4 circuit Not circuit malfunction
Shift solenoid valve SR circuit Not circuit malfunction
Shift solenoid valve DSL circuit Not circuit malfunction
OFF malfunction (A)
ECM selected gear 5th
Throttle valve opening angle 5% or more
Vehicle speed 10 km/h (6.2 mph) or more
OFF malfunction (B)
ECM lock-up command ON
ECM selected gear 3rd, 4th or 5th
Throttle valve opening angle 10% or more
Vehicle speed 25 to 100 km/h (15.5 to 62.1 mph)
ON malfunction (A)
ECM selected gear 4th or 5th
4.5% or more at engine speed 1,900 rpm
Throttle valve opening angle
(Varies with engine speed)
ON malfunction (B)
ECM selected gear 4th
Throttle valve opening angle 5% or more
Vehicle speed 10 km/h (6.2 mph) or more
TYPICAL MALFUNCTION THRESHOLDS
Either of the following conditions is met:
OFF malfunction (A) and (B), or ON malfunction (A) and (B)
2 detections are necessary per driving cycle:
1st detection; temporary flag ON
2nd detection; pending fault code ON
OFF malfunction (A)
Intermediate shaft speed/Output speed 1.44 to 1.58
OFF malfunction (B)
Difference between engine speed and input (turbine) speed Less than 35 rpm
ON malfunction (A)
Input (turbine) speed/Intermediate shaft speed 0.64 to 0.74
ON malfunction (B)
Intermediate shaft speed/Output speed 1.02 to 1.16
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 790
05-608 DIAGNOSTICS - ELECTRONIC CONTROLLED AUTOMATIC
TRANSAXLE [ECT]
INSPECTION PROCEDURE
HINT:
(a) Turn the ignition switch off.
(b) Connect the hand-held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Push the "ON" button of the hand-held tester.
(e) Select the item "DIAGNOSIS/ENHANCED OBD II/ACTIVE TEST/SHIFT".
(f) According to the display on tester, perform the "ACTIVE TEST".
HINT:
While driving, the shift position can be forcibly changed with the hand-held tester.
Comparing the shift position commanded by the ACTIVE TEST with the actual shift position enables you
to confirm the problem.
Item Test Details Diagnostic Note
[Test Details]
Operate the shift solenoid valve and set the each shift position by your-
self.
[Vehicle Condition] Possible to check the operation of
SHIFT
Less than 50 km/h (31 mph) the shift solenoid valves.
[Others]
S Press "" button: Shift up
S Press "" button: Shift down
HINT:
S This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
S The shift position commanded by the ECM is shown in the DATA LIST/SHIFT display on the hand-held
tester.
1 INSPECT SHIFT SOLENOID VALVE(S4)
(a) Remove the shift solenoid valve S4.
(-) (+) (b) Measure the resistance between the solenoid connector
and the solenoid body.
OK:
Resistance: 11 to 15 at 20◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo