Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 04 05 21q2h73z b163281
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download b163281 documenatation <<
Text preview - extract from the document
05-1013
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM 05NT7-01
DTC B1632/81 SHORT IN CURTAIN SHIELD SQUIB REAR
(RH) CIRCUIT (TO GROUND)
CIRCUIT DESCRIPTION
The curtain shield squib rear RH circuit consists of the airbag sensor assy center and the curtain shield airbag
assy RH.
The circuit instructs the SRS to deploy when deployment conditions are met.
DTC B1162/81 is recorded when a short to ground is detected in the curtain shield squib rear RH circuit.
DTC No. DTC Detecting Condition Trouble Area
S The airbag sensor assy center receives a short circuit to
ground signal in the curtain shield squib rear RH circuit for S Curtain shield airbag assy RH (Curtain shield squib rear RH)
B1162/81 0.5 seconds. S Airbag sensor assy center
S Curtain shield squib RH malfunction S Floor wire No.2
S Airbag sensor assy malfunction
WIRING DIAGRAM
See page 05-1006 .
INSPECTION PROCEDURE
1 CHECK FLOOR WIRE NO.2(CURTAIN SHIELD SQUIB REAR RH CIRCUIT)
(a) Turn the ignition switch to the LOCK position.
Floor Wire No.2 (b) Disconnect the negative (-) terminal cable from the bat-
Airbag tery, and wait for at least 90 seconds.
Curtain Shield Sensor (c) Disconnect the connectors from the airbag sensor assy
Squib Rear RH Assy center and the curtain shield airbag assy RH.
A Center (d) Measure the resistance according to the value(s) in the
D C B table below.
C17
Standard:
CR2+ CR2- Tester connection Condition Specified condition
C17-1 (CR2+) -
Always 1 M or Higher
Body ground
C17-2 (CR2-) -
Always 1 M or Higher
Body ground
H41465 H43068 NG REPAIR OR REPLACE FLOOR WIRE NO.2
OK
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1196
05-1014
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
2 CHECK AIR BAG SENSOR ASSY CENTER
(a) Connect the connector to the airbag sensor assy center.
Floor Wire No.2 Airbag (b) Using a service wire, connect C17-1 (CR2+) and C17-2
Curtain Shield Sensor (CR2-) of connector "C".
Squib Rear RH Assy NOTICE:
Center S Twist the end of the service wire in order to insert it
D C
C17 into the connector.
S Do not forcibly insert the twisted service wire into the
CR2+ CR2-
terminals of the connector when connecting.
Service Wire (c) Connect the negative (-) terminal cable to the battery,
and wait for at least 2 seconds.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
DLC3 DTC B1162/81 (e) Clear the DTCs stored in memory (see page 05-777 ).
(f) Turn the ignition switch to the LOCK position.
(g) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
CG TC (h) Check the DTCs (see page 05-777 ).
H01020 OK:
C89252
H10600 H11642 H42130 DTC B1162/81 is not output.
HINT:
Codes other than code B1162/81 may be output at this time, but
they are not related to this check.
NG REPLACE AIR BAG SENSOR ASSY CENTER
(SEE PAGE 60-56 )
OK
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1197
05-1015
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
3 CHECK CURTAIN SHIELD AIR BAG ASSY RH(CURTAIN SHIELD SQUIB REAR RH)
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the bat-
Airbag
tery, and wait for at least 90 seconds.
Curtain Shield Sensor (c) Disconnect the service wire from connector "C".
Squib Rear RH Assy (d) Connect the connector to the curtain shield airbag assy
Center RH.
DC (e) Connect the negative (-) terminal cable to the battery,
and wait for at least 2 seconds.
DLC3 DTC B1162/81 (f) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(g) Clear the DTCs stored in memory (see page 05-777 ).
(h) Turn the ignition switch to the LOCK position.
CG TC (i) Turn the ignition switch to the ON position, and wait for at
H01021
H10600 H11642 H40938 least 60 seconds.
(j) Check the DTCs (see page 05-777 ).
OK:
DTC B1162/81 is not output.
HINT:
Codes other than code B1162/81 may be output at this time, but
they are not related to this check.
NG REPLACE CURTAIN SHIELD AIR BAG ASSY RH
(SEE PAGE 60-40 )
OK
USE SIMULATION METHOD TO CHECK (SEE PAGE 05-770 )
HINT:
S Perform the simulation method by selecting the check mode with the hand-held tester (see page
05-780 ).
S After selecting the check mode, perform the simulation method by wiggling each connector of the air-
bag system or driving the vehicle on a city or rough road (see page 05-780 ).
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1198
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo