Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 04 05 21q2h73z b1783
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download b1783 documenatation <<
Text preview - extract from the document
05-1059
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM 05IWU-04
DTC B1783 OCCUPANT CLASSIFICATION SENSOR
REAR RH CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
The occupant classification sensor rear RH circuit consists of the occupant classification ECU and the occu-
pant classification sensor rear RH.
DTC B1783 is recorded when a malfunction is detected in the occupant classification sensor rear RH circuit.
DTC No. DTC Detecting Condition Trouble Area
S The occupant classification ECU receives a line short circuit
signal, an open circuit signal, a short circuit to ground signal S Seat adjuster frame assy
or a short circuit to B+ signal in the occupant classification (Occupant classification sensor rear RH)
B1783
sensor rear RH circuit for 2 seconds. S Front seat wire RH
S Occupant classification sensor rear RH malfunction S Occupant classification ECU
S Occupant classification ECU malfunction
HINT:
When DTC B1150/23 is detected as a result of troubleshooting for the supplemental restraint system, per-
form troubleshooting for DTC B1783 of the occupant classification system.
WIRING DIAGRAM
O8 Occupant Classification Sensor Rear RH Occupant Classification ECU
6
Y
O4 SVC4
1
10
L-W
O4 SIG4
2
4
R-W
3 O4 SGD4
H43062
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1242
05-1060
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
INSPECTION PROCEDURE
HINT:
S If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat assy instal-
lation bolts to see the under surface of seat cushion.
S In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time
may cause a problem, such as seat rail deformation. Hold the seat only as necessary.
1 CHECK DTC
(a) Turn the ignition switch to the ON position.
(b) Clear the DTCs stored in memory (see page 05-777 ).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assy center.
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position.
(e) Using the hand-held tester, check the DTCs (see page 05-777 ).
OK:
DTC B1783 is not output.
HINT:
Codes other than code B1783 may be output at this time, but they are not related to this check.
NG Go to step 2
OK
USE SIMULATION METHOD TO CHECK (SEE PAGE 05-770 )
2 CHECK CONNECTION OF CONNECTORS
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Check that the connectors are properly connected to the occupant classification ECU and the occu-
pant classification sensor rear RH.
OK:
The connectors are connected.
NG CONNECT CONNECTORS, THEN GO TO STEP
1
OK
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1243
05-1061
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
3 CHECK FRONT SEAT WIRE RH(TO B+)
(a) Disconnect the connectors from the occupant classifica-
Occupant Front Seat Wire RH tion ECU and the occupant classification sensor rear RH.
Classification Occupant (b) Connect the negative (-) terminal cable to the battery.
Sensor Rear RH Classification (c) Turn the ignition switch to the ON position.
ECU (d) Measure the voltage according to the value(s) in the table
D A below.
C B Standard:
O4 Tester connection Condition Specified condition
SGD4
O4-4 (SGD4) -
SVC4 Ignition switch ON Below 1 V
Body ground
O4-6 (SVC4) -
Ignition switch ON Below 1 V
Body ground
O4-10 (SIG4) -
SIG4 Ignition switch ON Below 1 V
Body ground
H43105
H43111 H43474
NG REPAIR OR REPLACE FRONT SEAT WIRE RH
OK
4 CHECK FRONT SEAT WIRE RH(OPEN)
Occupant Front Seat Wire RH (a) Turn the ignition switch to the LOCK position.
Classification Occupant (b) Disconnect the negative (-) terminal cable from the bat-
Sensor Rear RH Classification tery, and wait for at least 90 seconds.
ECU
(c) Using a service wire, connect O8-1 (SVC4) and O8-3
D A (SGD4), and connect O8-2 (SIG4) and O8-3 (SGD4) of
C B connector "C".
NOTICE:
O8 O4
Service Do not forcibly insert a service wire into the terminals of the
Wire SGD4 SVC4 connector when connecting.
(d) Measure the resistance according to the value(s) in the
SVC4 SGD4 table below.
Standard:
SIG4 Tester connection Condition Specified condition
H43106
Service Wire SIG4 O4-6 (SVC4) -
H43699 H43111 H43475
Always Below 1
O4-4 (SGD4)
O4-10 (SIG4) -
Always Below 1
O4-4 (SGD4)
NG REPAIR OR REPLACE FRONT SEAT WIRE RH
OK
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1244
05-1062
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
5 CHECK FRONT SEAT WIRE RH(SHORT)
(a) Disconnect the service wire from connector "C".
Occupant Front Seat Wire RH (b) Measure the resistance according to the value(s) in the
Classification Occupant table below.
Sensor Rear RH Classification
Standard:
ECU
Tester connection Condition Specified condition
D A O4-6 (SVC4) -
Always 1 M or Higher
C B O4-4 (SGD4)
O4-10 (SIG4) -
O4 Always 1 M or Higher
O4-4 (SGD4)
SGD4 SVC4 O4-6 (SVC4) -
Always 1 M or Higher
O4-10 (SIG4)
SIG4
H43105
H43111 H43474 NG REPAIR OR REPLACE FRONT SEAT WIRE RH
OK
6 CHECK FRONT SEAT WIRE RH(TO GROUND)
(a) Measure the resistance according to the value(s) in the
Occupant Front Seat Wire RH table below.
Classification Occupant Standard:
Sensor Rear RH Classification
Tester connection Condition Specified condition
ECU
O4-4 (SGD4) -
D Always 1 M or Higher
A Body ground
C B O4-6 (SVC4) -
Always 1 M or Higher
Body ground
O4 O4-10 (SIG4) -
SGD4 Always 1 M or Higher
SVC4 Body ground
SIG4
H43105
H43111 H43474 NG REPAIR OR REPLACE FRONT SEAT WIRE RH
OK
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1245
05-1063
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
7 RECHECK DTC
(a) Connect the connectors to the occupant classification ECU and the occupant classification sensor rear
RH.
(b) Connect the negative (-) terminal cable to the battery.
(c) Turn the ignition switch to the ON position.
(d) Clear the DTCs stored in memory (see page 05-777 ).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assy center.
(e) Turn the ignition switch to the LOCK position.
(f) Turn the ignition switch to the ON position.
(g) Using the hand-held tester, check the DTCs (see page 05-777 ).
OK:
DTC B1783 is not output.
HINT:
Codes other than code B1783 may be output at this time, but they are not related to this check.
NG Go to step 8
OK
USE SIMULATION METHOD TO CHECK (SEE PAGE 05-770 )
8 REPLACE OCCUPANT CLASSIFICATION ECU
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the occupant classification ECU (see page 60-67 ).
HINT:
Perform the inspection using parts from a normal vehicle if possible.
NEXT
9 PERFORM ZERO POINT CALIBRATION
(a) Connect the negative (-) terminal cable to the battery.
(b) Connect the hand-held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Using the hand-held tester, perform "Zero point calibration" (see page 05-767 ).
OK:
The "COMPLETED" is displayed.
NG Go to step 12
OK
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1246
05-1064
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
10 PERFORM SENSITIVITY CHECK
(a) Using the hand-held tester, perform "Sensitivity check" (see page 05-767 ).
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NG Go to step 12
OK
11 RECHECK DTC
(a) Connect the negative (-) terminal cable to the battery.
(b) Turn the ignition switch to the ON position.
(c) Clear the DTCs stored in memory (see page 05-777 ).
HINT:
First clear DTCs stored in the occupant classification ECU and then in the airbag sensor assy center.
(d) Turn the ignition switch to the LOCK position.
(e) Turn the ignition switch to the ON position.
(f) Using the hand-held tester, check the DTCs (see page 05-777 ).
OK:
DTC B1783 is not output.
HINT:
Codes other than code B1783 may be output at this time, but they are not related to this check.
NG Go to step 12
OK
END
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1247
05-1065
DIAGNOSTICS - SUPPLEMENTAL RESTRAINT SYSTEM
12 REPLACE SEAT ADJUSTER FRAME ASSY
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the seat adjuster frame assy (see page 72-30 ).
NEXT
13 PERFORM ZERO POINT CALIBRATION
(a) Connect the negative (-) terminal cable to the battery.
(b) Connect the hand-held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Using the hand-held tester, perform "Zero point calibration" (see page 05-767 ).
OK:
The "COMPLETED" is displayed.
NEXT
14 PERFORM SENSITIVITY CHECK
(a) Using the hand-held tester, perform "Sensitivity check" (see page 05-767 ).
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NEXT
END
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 1248
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo