Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 04 65 20ptj onvein40
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download onvein40 documenatation <<
Text preview - extract from the document
65-2
LIGHTING - LIGHTING SYSTEM
650PE-02
ON-VEHICLE INSPECTION
1. INSPECT TURN SIGNAL FLASHER CIRCUIT
(a) Measure voltage between the terminals as shown in the
chart below.
E15683
Standard:
Tester connection Condition Specified condition
1 - body ground Turn ignition switch ON 10 to 14 V
1 - body ground Turn ignition switch OFF No voltage
4 - body ground Always 10 to 14 V
7 - body ground Always Continuity
(b) Connect the connector to turn the signal flasher and turn
the ignition switch ON, and inspect the wire harness side
connector from the back side as shown in the chart.
Standard:
Tester connection Condition Specified condition
2 - body ground Hazard switch OFF ON 0V 10 to 14 V (60 to 120 time per minutes)
2 - body ground Turn signal switch (right turn) OFF ON 0V 10 to 14 V (60 to 120 time per minutes)
3 - body ground Hazard switch OFF ON 0V 10 to 14 V (60 to 120 time per minutes)
3 - body ground Turn signal switch (left turn) OFF ON 0V 10 to 14 V (60 to 120 time per minutes)
5 - body ground Turn signal switch (left turn) OFF ON 10 to 14 V 0 V
6 - body ground Turn signal switch (right turn) OFF ON 10 to 14 V 0 V
8 - body ground Hazard switch OFF ON 10 to 14 V 0 V
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3085
65-3
LIGHTING - LIGHTING SYSTEM
RH: 2. INSPECT HEADLAMP ASSEMBLY (HEADLIGHT
2 1 BEAM LEVEL CONTROL ACTUATOR OPERATION)
(a) Disconnect the connector from the headlamp assy.
(b) Connect the positive (+) lead from the battery to the termi-
3 nal 3 of each of the headlight beam level control actuator
LH: and negative (-) lead from the battery to the terminal 1 of
2 1 each of the headlight beam level control actuator.
(c) Connect the positive (+) lead from the battery to the termi-
nal 1 of the headlamp levering switch and negative (-)
lead from the battery to the terminal 2 of the headlamp le-
3
vering switch.
(d) Connect the terminal 4 of the headlamp leveling switch
and the terminal 2 of the headlight beam level control ac-
tuator LH, and connect the terminal 5 of the headlamp lev-
eling switch and the terminal 2 of the headlight beam level
control actuator RH.
(e) Measure voltage between each of the headlight beam
level control actuator and battery negative (-) terminal
E69031 when headlamp levering switch is operated.
Standard:
Switch position Specified voltage (V)
0 9.0 to 12.6
1 7.9 to 11.1
2 6.9 to 9.6
3 5.8 to 8.2
4 4.7 to 6.6
5 3.7 to 5.1
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3086
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo