Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 09 203en x040001
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download x040001 documenatation <<
Text preview - extract from the document
14-154
ENGINE MECHANICAL - ENGINE REAR OIL SEAL
ENGINE REAR OIL SEAL
1405R-06
REPLACEMENT
1. REMOVE AUTOMATIC TRANSAXLE ASSY (2WD DRIVE TYPE) (See page 40-9 )
2. REMOVE AUTOMATIC TRANSMISSION W/TRANSFER (4WD DRIVE TYPE) (See page 40-9 )
3. REMOVE DRIVE PLATE & RING GEAR SUB-ASSY
(a) Using SST, hold the crankshaft.
SST 09213-54015 (91651-60855), 09330-00021
(b) Remove the 8 bolts, the rear spacer, the drive plate and
the front spacer.
SST
A78767
4. REMOVE ENGINE REAR OIL SEAL
Cut position
(a) Using a knife, cut off the oil seal lip.
(b) Using a screwdriver with the tip wrapped in tape, pry out
the oil seal.
NOTICE:
Cut position After the removal, check if the crankshaft is not damaged.
If it is damaged, smooth the surface with 400-grit sandpa-
per.
A78768
5. INSTALL ENGINE REAR OIL SEAL
SST (a) Apply MP grease to a new oil seal lip.
NOTICE:
Keep the lip off foreign materials.
(b) Using SST and a hammer, tap in the oil seal until its sur-
face is flush with the rear oil seal retainer edge.
SST 09223-15030, 09950-70010 (09951-07100)
NOTICE:
A78769 S Be careful not to tap the oil seal slantingly.
S Wipe off extra grease on the crankshaft.
6. INSTALL DRIVE PLATE & RING GEAR SUB-ASSY
(a) Using SST, hold the crankshaft.
SST 09213-54015 (91651-60855), 09330-00021
(b) Clean the bolts and the bolt holes.
(c) Apply adhesive to 2 or 3 threads of the bolts.
Adhesive: Part No. 08833-00070, THREE BOND 1324
SST or equivalent
(d) Install the front spacer, the drive plate and the rear spacer
A78767 on the crankshaft.
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 2453
14-155
ENGINE MECHANICAL - ENGINE REAR OIL SEAL
1 (e) Using several steps, install and tighten the 8 bolts uni-
5
formly in the sequence shown in the illustration.
7
Torque: 83 Nm (846 kgfcm, 61 ftlbf)
NOTICE:
3 Do not start the engine within an hour after installing.
4
8
6
2 A78771
7. INSTALL AUTOMATIC TRANSMISSION W/TRANSFER (4WD DRIVE TYPE) (See page 40-9 )
8. INSTALL AUTOMATIC TRANSAXLE ASSY (2WD DRIVE TYPE) (See page 40-9 )
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 2454
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo