Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 27 203uc x040001

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.



Image preview - the first page of the document



>> Download x040001 documenatation <<

Text preview - extract from the document

60-56
                     SUPPLEMENTAL RESTRAINT SYSTEM      -   AIR BAG SENSOR ASSY CENTER
                                                                                                       6009A-11


REPLACEMENT
1.      PRECAUTION (SEE PAGE 60-1 )
2.      DISCONNECT BATTERY NEGATIVE TERMINAL (SEE PAGE 60-1 )
3.      REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSY LOWER LH (SEE PAGE 71-10 )
4.      REMOVE FLOOR CARPET COVER CENTER LH (SEE PAGE 71-10 )
5.      REMOVE FLOOR CARPET COVER CENTER RH (SEE PAGE 71-10 )
6.      REMOVE GLOVE COMPARTMENT DOOR ASSY (SEE PAGE 71-10 )
7.      REMOVE INSTRUMENT PANEL BOX NO.2 (SEE PAGE 71-10 )
8.      REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSY CENTER (SEE PAGE 71-10 )
9.      REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSY LOWER CENTER (SEE PAGE
        71-10 )
10.     REMOVE AIR DUCT REAR NO.4 (SEE PAGE 71-10 )
11.     REMOVE AIR DUCT REAR NO.3 (SEE PAGE 71-10 )
12.     REMOVE AIR DUCT REAR NO.1 (SEE PAGE 71-10 )

                                                13.   REMOVE AIR BAG SENSOR ASSY CENTER
                                                (a)   Disconnect the 3 connectors from the airbag sensor assy
                                                      center.
                                                (b)   Remove the 3 bolts and the airbag sensor assy center.




                                       H42688



14. INSTALL AIR BAG SENSOR ASSY CENTER
(a) Check that the ignition switch is OFF.
(b) Check that the battery negative (-) terminal is disconnected.
NOTICE:
Do not start the operation for 90 seconds after removing the terminal.
(c) Temporarily install the airbag sensor assy center with the 3 bolts.
NOTICE:
 S  Installation of the connector is performed with the airbag sensor assy center installed. Make
    sure the airbag sensor assy center is installed with the specified torque.
 S  If the airbag sensor assy center has been dropped, or there are cracks, dents or other defects
    in the case, bracket or connector, replace the airbag sensor assy center with a new one.
 S  When installing the airbag sensor assy center, take care that the SRS wiring does not interfere
    with other parts and is not pinched between other parts.
(d) Tighten the 3 bolts to the specified torque.
    Torque: 17.5 Nm (178 kgfcm, 13 ftlbf)
(e) Connect the connector to the air bag sensor assy center.
(f) Check that no play is identified.
(g) Check that the water-proof sheet is properly set.
15. INSPECT SRS WARNING LIGHT (SEE PAGE 05-770 )




 2005 SIENNA REPAIR MANUAL (RM1163U)

                                                                  Author :               Date :          3051

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo