Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 27 203uh x040001

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.



Image preview - the first page of the document



>> Download x040001 documenatation <<

Text preview - extract from the document

60-60
                    SUPPLEMENTAL RESTRAINT SYSTEM      -   SIDE AIR BAG SENSOR ASSY LH
                                                                                                    6009G-12


REPLACEMENT
HINT:
Replacement procedure of the RH side is the same as that of the LH side.
1.    PRECAUTION (SEE PAGE 60-1 )
2.    DISCONNECT BATTERY NEGATIVE TERMINAL (SEE PAGE 60-1 )
3.    REMOVE FRONT DOOR SCUFF PLATE LH (SEE PAGE 71-10 )
4.    REMOVE REAR DOOR SCUFF PLATE LH (SEE PAGE 76-27 )
5.    REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (SEE PAGE 71-10 )
6.    REMOVE REAR DOOR WEATHERSTRIP LH (SEE PAGE 76-27 )
7.    REMOVE LAP BELT OUTER ANCHOR COVER LH (SEE PAGE 76-27 )
8.    REMOVE CENTER PILLAR GARNISH LOWER LH (SEE PAGE 76-27 )
9.    REMOVE FRONT SEAT OUTER BELT ASSY LH (SEE PAGE 61-7 )



                                               10.   REMOVE SIDE AIR BAG SENSOR ASSY LH
                                               (a)   Remove the 2 nuts and the side airbag sensor assy LH.
                                               (b)   Disconnect the connector from the side airbag sensor
                                                     assy LH.




                                      H42693



11. INSTALL SIDE AIR BAG SENSOR ASSY LH
(a) Check that the ignition switch is OFF.
(b) Check that the battery negative (-) terminal is disconnected.
NOTICE:
Do not start the operation for 90 seconds after removing the terminal.
(c) Install the side airbag sensor assy LH with the 2 nuts.
    Torque: 17.5 Nm (178 kgfcm, 13 ftlbf)
NOTICE:
 S  Installation of the connector is performed with the side airbag sensor assy LH installed. Make
    sure the side airbag sensor assy LH is installed with the specified torque.
 S  If the side airbag sensor assy LH has been dropped, or there are cracks, dents or other defects
    in the case, bracket or connector, replace the side airbag sensor assy LH with a new one.
 S  When installing the side airbag sensor assy LH, take care that the SRS wiring does not interfere
    with other parts and is not pinched between other parts.
(d) Connect the connector of the side airbag sensor assy LH.
(e) Check that no play is identified.
12. INSTALL FRONT SEAT OUTER BELT ASSY LH (SEE PAGE 61-7 )
13. INSPECT SRS WARNING LIGHT (SEE PAGE 05-770 )




2005 SIENNA REPAIR MANUAL (RM1163U)

                                                                  Author :               Date :       3055

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo