Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 28 20muh x040001

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.




Image preview - the first page of the document
x040001


>> Download x040001 documenatation <<

Text preview - extract from the document
                                                                                                           61-7
                                                 SEAT BELT   -   FRONT SEAT BELT
                                                                                                          610AM-06


REPLACEMENT
HINT:
S       The installation is in the reverse order of the removal. However, when there is a special point concern-
        ing the installation, it is indicated.
S       On the LH side, use the same procedures as on the RH side.
1.      DISCONNECT BATTERY NEGATIVE TERMINAL
2.      REMOVE FRONT SEAT ASSEMBLY RH (See page 72-12 , 72-22 )
3.      REMOVE FRONT SEAT INNER BELT ASSY RH
(a)     Remove the nut and inner belt.
4.      REMOVE FRONT DOOR SCUFF PLATE RH (See page 76-27 )
5.      REMOVE REAR DOOR SCUFF PLATE RH (See page 76-27 )
6.      REMOVE FRONT DOOR WEATHERSTRIP RH (See page 76-27 )
7.      REMOVE REAR DOOR WEATHERSTRIP RH (See page 76-27 )
8.      REMOVE CENTER PILLAR GARNISH LOWER RH (See page 76-27 )
9.      REMOVE CENTER PILLAR GARNISH UPPER RH (See page 76-27 )
                                                 10. REMOVE FRONT SEAT OUTER BELT ASSY RH
                                                 NOTICE:
                                                  S     Removal operation concerning the seat belt with the
                                                        pretensioner must be started in 90 seconds or more
                                                        after the ignition switch is turned OFF and the battery
                                                        negative terminal is disconnected.
                                                  S     Carefully read the notices for the "pretensioner" in
                                                        the SRS airbag system and the outer belt assy.
                                                 (a) Remove the nut and the front seat outer belt on the shoul-
                                                        der anchor side.




                                                   (b)   Disconnect the pretensioner connector, as shown in the
                                                         illustration.
                                                   (c)   Remove the 2 bolts and outer belt.




                                        B69495



11.     REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSY
(a)     Remove the bolt and anchor adjuster.
12.     INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSY
(a)     Install the anchor adjuster with the bolt.
        Torque: 42 Nm (430 kgfcm, 31 ftlbf)




 2005 SIENNA REPAIR MANUAL (RM1163U)

                                                                       Author :        Date :             3069
61-8
                                            SEAT BELT   -   FRONT SEAT BELT

                                            13. INSTALL FRONT SEAT OUTER BELT ASSY RH
       Unlock          45_                  NOTICE:
                                            Do not disassemble the retractor.
                                            (a) Check the degree of tilt when beginning to lock the ELR.
                                                  (1) Check that the belt does not lock within 15_ of tilt in
                                    Lock
                                                         all directions but that the belt locks with over 45_ of
                                                         tilt, when gently moving the retractor.
   Retractor                                If operation is not as specified, replace the outer belt assy.
                                     B69492 (b) Install the retractor with the 2 bolts.
                                                  Torque: 42 Nm (430 kgfcm, 31 ftlbf)
                                            (c) Install the shoulder anchor with the nut.
                                                  Torque: 42 Nm (430 kgfcm, 31 ftlbf)
                                            (d) Install the center pillar garnish upper RH
                                                  (See page 76-27 ).
                                            (e) Install the center pillar garnish lower RH
                                                  (See page 76-27 ).
                                            (f)   Install the floor anchor with the bolt.
                                                  Torque: 42 Nm (430 kgfcm, 31 ftlbf)
                                            (g) Install the floor anchor cover.
                                            (h) Check the ELR lock.
                                            NOTICE:
                                            The check should be performed with the assembly
                                            installed.
                                                  (1) Check that the belt locks when pulling out the belt
                                                         quickly when the belt is installed.
                                            If operation is not as specified, replace the outer belt assy.
                                            (i)   Check the fastening function of the child restraint system.
                                            NOTICE:
                                            The check should be performed with the assembly
                                            installed.
                                                  (1) Check that the belt cannot be pulled out any more
                                                         but can be rewound after the belt is fully pulled out.
                                                  (2) Check that the belt can be pulled out and rewound
                                                         after the belt is fully rewound.
                                            If operation is not as specified, replace the belt assy.
14. INSTALL FRONT SEAT INNER BELT ASSY RH
(a) Install the inner belt with the nut.
    Torque: 42 Nm (430 kgfcm, 31 ftlbf)




 2005 SIENNA REPAIR MANUAL (RM1163U)

                                                                   Author :           Date :               3070



◦ Jabse Service Manual Search 2026 ◦ Jabse PravopisonTap.bg ◦ Other service manual resources online : FixyaeServiceinfo