Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 21 32 2042jl01 x040001
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download x040001 documenatation <<
Text preview - extract from the document
32-50
BRAKE - SKID CONTROL SENSOR (FF)
SKID CONTROL SENSOR (FF)
320V3-01
REPLACEMENT
HINT:
Replace the RH side by the same procedure as the LH side.
1. REMOVE REAR WHEEL
2. SEPARATE SKID CONTROL SENSOR WIRE
(a) Disconnect the connector from the skid control sensor.
G24268
3. REMOVE REAR BRAKE DRUM SUB-ASSY (DRUM REAR BRAKE TYPE)
(a) Place matchmarks on the rear brake drum sub-assy and the axle hub.
(b) Remove the rear brake drum sub-assy.
4. REMOVE REAR DISC BRAKE CALIPER ASSY LH (DISC REAR BRAKE TYPE)
(a) Remove the 2 bolts and rear brake caliper assy LH.
5. REMOVE REAR DISC (DISC REAR BRAKE TYPE)
(a) Place matchmarks on the rear disc and the axle hub.
(b) Remove the rear disc.
6. REMOVE REAR AXLE HUB & BEARING ASSY LH (See page 30-46 )
7. REMOVE SKID CONTROL SENSOR
(a) Mount the rear axle hub in a soft jaw vise.
NOTICE:
Replace the axle hub assembly if it is dropped or a strong
shock is given to it.
(b) Using a pin punch and hammer, drive out the 2 pins and
SST
remove the 2 attachments from SST.
(c) Using SST and 2 bolts (Diameter: 12 mm, pitch: 1.5 mm),
remove the skid control sensor from the rear axle hub.
SST 09520- 00031 (09520- 00040), 09521- 00020,
Bolt 09950-00020
NOTICE:
S If a damage is inflicted to the sensor rotor is dam-
aged, replace the axle hub assembly.
S Do not scratch the contacting surface of the axle hub
and speed sensor.
SST
F40303
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 2798
32-51
BRAKE - SKID CONTROL SENSOR (FF)
8. INSTALL SKID CONTROL SENSOR
(a) Clean the contacting surface of the axle hub and a new
skid control sensor.
NOTICE:
Keep the sensor rotor clean.
(b) Place the speed sensor on the axle hub so that the con-
nector is positioned as shown in the illustration.
G23168
(c) Using SST and a press, install the skid control sensor to
the axle hub.
SST 09214-7601 1
SST
NOTICE:
S Do not tap the skid control sensor with a hammer di-
rectly.
S Check that there is no foreign matter on the skid con-
trol sensor detection portion.
F40304 S Press in the skid control sensor straight and slowly.
9. INSTALL REAR AXLE HUB & BEARING ASSY LH (See page 30-46 )
10. INSTALL REAR BRAKE DRUM SUB-ASSY (DRUM REAR BRAKE TYPE)
(a) Aligning the matchmarks, install the rear brake drum sub-assy.
11. INSTALL REAR DISC (DISC REAR BRAKE TYPE)
(a) Aligning the matchmarks, install the rear disc.
12. INSTALL REAR DISC BRAKE CALIPER ASSY LH (DISC REAR BRAKE TYPE)
(a) Install the rear disc brake caliper assy LH with the 2 bolts.
Torque: 88 Nm (900 kgfcm, 65 ftlbf)
13. CONNECT SKID CONTROL SENSOR WIRE
(a) Connect the connector to the skid control sensor connec-
tor.
G24268
14. INSTALL REAR WHEEL
Torque: 103 Nm (1,050 kgfcm, 76 ftlbf)
15. INSPECT AND ADJUST REAR WHEEL ALIGNMENT (See page 27-4 )
16. CHECK ABS SPEED SENSOR SIGNAL (See page 05-386 )
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 2799
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo