Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 21 32 20uks w040001

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document
w040001

>> Download w040001 documenatation <<

Text preview - extract from the document

32-37
BRAKE - REAR DISC BRAKE
320V7-02

OVERHAUL
HINT:
Overhaul the RH side by the same procedure as the LH side.
1. REMOVE REAR WHEEL
2. DRAIN BRAKE FLUID
NOTICE:
Wash the brake fluid off immediately if it attaches to any painted surface.

3. SEPARATE REAR BRAKE TUBE NO.4
(a) Remove the clip and a disconnect, the rear brake flexible
hose.
(b) Using SST and spanner loosen the rear brake tube No.4.
SST 09023-00101

C65884

4. SEPARATE REAR LH FLEXIBLE HOSE
(a) Using SST, remove the rear brake flexible hose.
SST 09023-12701

C90476

5. REMOVE DISC BRAKE CYLINDER ASSY REAR LH
(a) Hold the rear disc brake cylinder slide pin and remove the
2 bolts.
(b) Remove the disc brake cylinder assy rear LH from the rear
disc brake cylinder mounting LH.

C85507

6. REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN
(a) Remove the 2 rear disc brake cylinder slide pins from the rear disc brake cylinder mounting LH.
7. REMOVE REAR DISC BRAKE BUSH DUST BOOT
(a) Remove the 2 rear disc brake bush dust boots.
8. REMOVE DISC BRAKE PAD KIT REAR (PAD ONLY)
(a) Remove the disc brake pad kit rear.
9. REMOVE REAR DISC BRAKE ANTI SQUEAL SHIM KIT
(a) Remove the anti squeal shim No.1 and anti squeal shim No.2 from each pad.

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 2785
32-38
BRAKE - REAR DISC BRAKE

10. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE
(a) Remove the rear disc brake pad support plate (No.1) and rear disc brake pad support plate (No.2)
from the rear disc brake cylinder mounting LH.
11. REMOVE REAR DISC BRAKE CYLINDER MOUNTING LH
(a) Remove the bolts and rear disc brake cylinder mounting LH.
12. REMOVE CYLINDER BOOT
(a) Using a screwdriver, remove the set ring and cylinder
boot.

F12033

13. REMOVE REAR DISC BRAKE DISC BRAKE PISTON
(a) Place a shop rug, between the rear disc brake piston and
the disc brake cylinder.
(b) Use compressed air to remove the rear disc brake piston
from the disc brake cylinder.
CAUTION:
Do not place your fingers in front of the piston when using
compressed air.
F12034 NOTICE:
Do not spatter the brake fluid.
14. REMOVE PISTON SEAL
(a) Using a screwdriver, remove the piston seal from the disc
brake cylinder assy rear LH.
NOTICE:
Do not damage the inner cylinder and cylinder groove.

F12035

15. REMOVE REAR DISC BRAKE BLEEDER PLUG CAP
16. REMOVE REAR DISC BRAKE BLEEDER PLUG
(a) Remove the rear disc brake bleeder plug from the disc brake cylinder assy rear LH.
17. INSPECT BRAKE CYLINDER AND PISTON
(a) Check the brake cylinder bore and rear disc brake piston for rust or scoring.
18. INSPECT PAD LINING THICKNESS
(a) Using a ruler, measure the pad lining thickness.
Standard thickness: 11.0mm (0.433 in.)
Minimum thickness: 1.0 mm (0.039 in.)

F45358

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 2786
32-39
BRAKE - REAR DISC BRAKE

19. INSPECT REAR DISC BRAKE PAD SUPPORT PLATE
(a) Inspect the rear brake disc pad support plate (No.1) and rear brake disc pad support plate (No.2).
Make sure that they have sufficient rebound, no deformation, cracks or wear, and have had all rust and
dirt cleaned off.
20. INSPECT DISC THICKNESS
(a) Using a micrometer, measure the disc thickness.
Standard thickness: 12.0mm (0.472 in.)
Minimum thickness: 10.5 mm (0.413 in.)

21. REMOVE REAR DISC
(a) Make matchmarks on the rear disc and the axle hub,
(b) Remove the rear disc.
22. INSTALL REAR DISC
(a) Aligning the matchmarks, install the rear disc.
HINT:
Select the installation position where the disc has the minimum
runout.
F41543

23. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG
24. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

25. INSPECT DISC RUNOUT
(a) Temporarily fasten the disc with the hub nuts.
Torque: 103 Nm (1,050 kgfcm, 76 ftlbf)
(b) Using a dial indicator, measure the disc runout 10 mm
(0.39 in.) away from the outer edge of the disc.
Maximum disc runout: 0.10 mm (0.0039 in.)
(c) If the disc runout is the maximum value or greater, check
the bearing play in the axial direction and check for the
C65886 axle hub runout (See page 30-3 ). If the bearing play and
axle hub runout are normal, adjust the disc runout or grind
it on a "On-car" brake lathe.

26. ADJUST PARKING BRAKE SHOE CLEARANCE (See page 33-2 )
27. TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG
(a) Temporarily install the rear disc brake bleeder plug to the disc brake cylinder assy rear LH.
28. INSTALL REAR DISC BRAKE BLEEDER PLUG CAP
29. INSTALL PISTON SEAL
(a) Apply lithium soap base glycol grease to a new piston seal.
(b) Install the piston seal to the disc brake cylinder assy rear LH.

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 2787
32-40
BRAKE - REAR DISC BRAKE

30. INSTALL REAR DISC BRAKE PISTON
(a) Apply lithium soap base glycol grease to the rear disc
brake piston and new cylinder boot.
(b) Install the cylinder boot to the rear disc brake piston .
(c) Install the rear disc brake piston to the disc brake cylinder
assy rear LH.
NOTICE:
Do not install the piston forcibly in the disc brake cylinder.
G24295

31. INSTALL CYLINDER BOOT
(a) Install a new cylinder boot to the rear disc brake cylinder
sub-assy .
NOTICE:
Install the boot securely to the grooves of the cylinder and
piston.
(b) Using a screwdriver, install the set ring.
NOTICE:
G24294 Do not damage the cylinder boot.

32. INSTALL REAR DISC BRAKE BUSH DUST BOOT
(a) Install the 2 rear disc brake bush dust boot to the disc brake cylinder mounting LH.
33. INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN
(a) Apply the lithium soap base glycol grease to the sealing surface of the 2 rear disc brake cylinder slide
pins.
34. INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH
(a) Install the rear disc brake cylinder mounting LH with the 2 bolts.
Torque: 88 Nm (900 kgfcm, 65 ftlbf)
35. INSTALL REAR DISC BRAKE PAD SUPPORT PLATE
(a) Install the rear disc brake pad support plate (No.1) and rear disc brake pad support plate (No.2) to the
rear disc brake cylinder mounting LH.
36. INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT
NOTICE:
If necessary, replace the anti squeal shim kit when replacing the brake pad.
(a) Apply disc brake grease to each anti squeal shim No.1.
(b) Install anti squeal shims No.1 and anti squeal shim No.2 on each pad.
37. INSTALL DISC BRAKE PAD KIT REAR (PAD ONLY)
(a) Install the brake pad kit rear to the rear disc brake cylinder mounting LH.
NOTICE:
There should be no oil or grease on the friction surfaces of the pads and the disc.
38. INSTALL DISC BRAKE CYLINDER ASSY REAR LH
(a) Install the disc brake cylinder assy rear LH with the 2 bolts.
Torque: 34 Nm (350 kgfcm, 25 ftlbf)

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 2788
32-41
BRAKE - REAR DISC BRAKE

39. CONNECT REAR LH FLEXIBLE HOSE
(a) Using SST, Install the rear brake flexible hose.
SST 09023-12701
Torque: 23 Nm (235 kgfcm, 17 ftlbf)

C90476

40. CONNECT REAR BRAKE TUBE NO.4
(a) Install the clip and connect the rear brake flexible hose.
(b) Using SST and a spanner, connect the rear brake tube
No.4.
SST 09023-00101
Torque: 15 Nm (155 kgfcm, 11 ftlbf)

C65884

41. FILL RESERVOIR WITH BRAKE FLUID (See page 32-4 )
42. BLEED MASTER CYLINDER (See page 32-4 )
SST 09023-00101
43. BLEED BRAKE LINE (See page 32-4 )
44. CHECK FLUID LEVEL IN RESERVOIR (See page 32-4 )
45. CHECK BRAKE FLUID LEAKAGE
46. INSTALL REAR WHEEL
Torque: 103 Nm (1,050 kgfcm, 76 ftlbf)

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 2789

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo