Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 37 20mtp i740001
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download i740001 documenatation <<
Text preview - extract from the document
73-14
THEFT DETERRENT & DOOR LOCK - DOOR CONTROL TRANSMITTER
DOOR CONTROL TRANSMITTER
730E8-02
INSPECTION
1. INSPECT DOOR CONTROL TRANSMITTER
(a) Inspect operation of the transmitter.
(1) Remove the battery (lithium battery) from the transmitter (See page 73-13 ).
(2) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery is not available, connect 2 new
1.5 V batteries in series, connect the battery positive (+) to the
battery receptacle side terminal and battery negative (-) to the
bottom terminal, then apply 3 V voltage to the transmitter.
B62233
(3) In a location that is approx. 1 m (3.28 ft) away from the driver side outside door handle in the right
direction, point the key plate of the transmitter at the vehicle and check operation of the transmit-
ter by pressing a transmission switch on the transmitter body.
Standard:
The door lock can be operated via the remote control.
HINT:
S The minimum operational distance differs, depending on the operator, the way the transmitter is held,
and the location.
S Since the transmitter uses faint electric waves, the operational distance might be shortened if noise
or strong electric wave occurs in the area where the frequency is used.
(4) Install the battery (lithium battery).
(b) Inspect the battery capacity.
HINT:
S The capacity of the battery can be determined only when the battery is installed in the transmitter. For
a lithium battery used in the transmitter, a voltage of more than 2.5 V is shown on the tester until the
energy is completely consumed, while no battery is installed in the transmitter. Therefore, it is neces-
sary to measure the voltage while the battery is installed in transmitter (a resistance of 1.2 k is applied
to the battery) when checking the amount of energy left in the battery.
S If the transmitter is faulty, the amount of energy left in the battery might not be checked correctly.
(1) Remove the battery (lithium battery) from the transmitter (See page 73-13 ).
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3322
73-15
THEFT DETERRENT & DOOR LOCK - DOOR CONTROL TRANSMITTER
(2) Connect the lead to the negative (-) terminal of the
transmitter and install the battery.
Lead
B62236
(3) Connect the tester positive (+) probe to the positive
(+) battery (lithium battery) and the tester negative
(-) probe to the lead respectively.
(4) Press one of the transmission switches on the
transmitter for approx. 1 second.
(5) Press the transmission switch on the transmitter
again to check the voltage.
Standard: 2.2 V or higher
B62232
HINT:
S When the temperature of the battery is low, the inspection can not be made correctly.
When the outcome of the test is less than 2.2 V, conduct the test again after leaving the battery in a
place at 18◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo