Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 39 20uh5 w040001

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document
w040001

>> Download w040001 documenatation <<

Text preview - extract from the document

75-48
ENGINE HOOD/DOOR - SLIDE DOOR
750LZ-02

OVERHAUL
HINT:
S The installation is in the reverse order of the removal. However, when there is a special point concern-
ing the installation, it is indicated.
S On the RH side, use the same procedures as on the LH side.
1. REMOVE REAR DOOR WINDOW FRAME MOULDING REAR LH (See page 76-15 )
2. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSY LH (See page 76-13 )

3. REMOVE SLIDE DOOR WINDOW GARNISH LH
(a) Fully open the slide door window.
(b) Remove the glass run.
(c) Using a screwdriver, disengage the clip and remove the
garnish.
HINT:
Clip
Tape the screwdriver tip before use.
(d) Using a screwdriver, disengage the 2 claws and remove
B67492 the weatherstrip inner from the garnish.
HINT:
Tape the screwdriver tip before use.

4. REMOVE SIDE TRIM BOARD COVER REAR LH
1 (a) Remove the 2 screws.
(b) Using a screwdriver, disengage the 8 claws and remove
5 1 the cover together with the window control switch.
HINT:
Tape the screwdriver tip before use.
(c) Remove the 2 screws and window control switch.
4 2
: Claw 3 2

5
4 3

B67491

Protective 5. REMOVE REAR DOOR TRIM BOARD SUB-ASSY LH
Tape (a) Remove the screw.
(b) Using a screwdriver, disengage the 9 clips and remove
Protective
Tape
the trim board.
HINT:
S Tape the screwdriver tip before use.
S In order to prevent the door panel from being damaged,
: Clip
cover the areas with protective tape as indicated by arrow
B67493
B67513 B69309 marks in the illustration.

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 3409
75-49
ENGINE HOOD/DOOR - SLIDE DOOR

(c) Using a clip remover, remove the 6 clips and weatherstrip
No. 2.
(d) Using a screwdriver, disengage the 11 claws and remove
the weatherstrip inner from trim board.
HINT:
Tape the screwdriver tip before use.

(e) w/ Sunshade:
Bezel Remove the sunshade.
Curtain
(1) Remove the 7 screws and sunshade bezel.
(2) (2) Remove the 4 screws and curtain.

(1)
B67513 B69307

6. REMOVE SLIDE DOOR WINDOW ASSY LH
(a) w/ Sunshade:
Remove the sunshade hook.
(b) Remove the bolt and window frame.

B69208

(c) Remove the bolt.
(d) Loosen the nut.
(e) Push the window frame rear lower in the direction indi-
cated by the arrow mark in the illustration.

B67495

(f) Remove the 2 hole plugs.
(g) Move the window until the bolts appear in the service
holes.
NOTICE:
S Do not damage the window assy.
S When the bolts are removed, the window assy may
fall and become deformed.
(h) Remove the 2 bolts and window.
B67494

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 3410
75-50
ENGINE HOOD/DOOR - SLIDE DOOR

7. REMOVE REAR DOOR GLASS WEATHERSTRIP ASSY OUTER LH (See page 76-18 )
8. REMOVE SLIDE DOOR
(a) Remove the rear door scuff plate (See page 76-27 ).
(b) Remove the back door scuff plate (See page 76-27 ).
(c) Remove the quarter trim pane (See page 76-27 ).
(d) Remove the upper rail cushion from the rail upper.

(e) Disconnect the 2 connectors from the body side and re-
move the bolt and wire.

B68386

(f) Open the quarter glass.
(g) Using a screwdriver, disengage the clip and 2 claws, re-
move the rail end moulding.
HINT:
Tape the screwdriver tip before use.

Claw
Clip B68589

(h) Remove the 2 bolts and bracket center No. 2.

Bracket

B68936 B69321

(i) Remove the 2 nuts and open stop.

B67901

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 3411
75-51
ENGINE HOOD/DOOR - SLIDE DOOR

Roller Lower (j) Rotate the base of the slide door roller lower in the direc-
tion indicated by arrow in the illustration and then remove
Rail Lower the roller from the cut area of the lower rail from the body
side.

B60924

(k) Move the slide door rearward and then remove the slide
Roller Upper
door roller upper from the cut area in the rear part of the
slide door rail upper.

Rail Upper
B69213

(l) Move the slide door further rearward and then remove the
Rail Center slide door hinge center from the rear part of the slide door
rail center. Then, remove the slide door.

Hinge Center

B69212

9. REMOVE SLIDE DOOR RAILS
(a) Remove the roof headlining (See page 76-27 ).
(b) Remove the 2 bolts, 2 nuts and the rail upper.
(c) Remove the 2 screws and the rear side rail.
(d) Remove the 3 screws and the rail center.
10. REMOVE SLIDE DOOR ATTACHMENT CONTROL LH
(a) Remove the 2 screws, bolt and inside handle.

B67507 B69312

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 3412
75-52
ENGINE HOOD/DOOR - SLIDE DOOR

(b) Disconnect the connectors from the lock actuator and
power window regulator motor.
(c) Disengage the control cables.
(d) Remove the 8 bolts and attachment control.

B67500

(e) Remove the nut and the window frame rear lower.
NOTICE:
When the nut is removed, the window frame may fall and
become deformed.
HINT:
Remove the window frame rear lower through the service hole.

B67495 B69308

(f) Remove the control rod.
(g) Remove the 3 bolts and lock remote control.

B67508

(h) Remove the 2 screws and lock actuator.

B67508

(i) Remove the 3 screws and power window regulator motor.

B67508

2005 SIENNA REPAIR MANUAL (RM1163U)

Author : Date : 3413
75-53
ENGINE HOOD/DOOR - SLIDE DOOR

(j) Remove the half stop control lever and door lock control
bellcrank.
(k) Remove the 4 bolts and window regulator.

B68933

11. REMOVE REAR DOOR STIFFENER CUSHION LH
(a) Remove 2 hole plugs.
(b) Remove the 2 screws, clip and stiffener cushion.
HINT:
Remove the stiffener cushion through the service hole.
(c) Remove the 2 grommets and 2 clips.

B67511

12. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH
(a) Remove the hole plug.
(b) Using a torx

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo