Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 39 20uh3 a040001
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download a040001 documenatation <<
Text preview - extract from the document
75-2
ENGINE HOOD/DOOR - HOOD
750LT-01
ADJUSTMENT
HINT:
Since a centering bolt is used as a hood hinge mounting bolt
and hood lock mounting bolt, the hood and hood lock can not
be adjusted with them on. Substitute a bolt with a washer for the
centering bolt.
Centering Bolt Standard Bolt
B57104
1. INSPECT HOOD SUB-ASSY
(a) Check that the clearance is within the standard range.
B
C
D
E
A
B67477
Standard:
A 8.0 " 1.5 mm (0.315 " 0.059 in.)
B 4.0 " 1.5 mm (0.157 " 0.059 in.)
C 0.4 " 1.5 mm (0.015 " 0.059 in.)
D 5.0 " 1.5 mm (0.197 " 0.059 in.)
E 1.1 " 1.5 mm (0.043 " 0.059 in.)
2. ADJUST HOOD SUB-ASSY
(a) Horizontally adjust the hood.
(1) Loosen the 4 hood hinge mounting bolts on the
hood side.
B62399
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3363
75-3
ENGINE HOOD/DOOR - HOOD
(2) Adjust the clearance by moving the hood, so that it
will be in the standard range.
A
Standard (A): 4.0 " 1.5 mm (0.157 " 0.059 in.)
(3) Tighten the hood side hinge bolts after the adjust-
ment.
Torque: 13 Nm (130 kgfcm, 10 ftlbf)
Aligned
B67478
(b) Adjust the height of the hood front end using the cushion
rubber.
(1) Adjust the cushion rubber so that the hood and the
fender will be aligned.
HINT:
The cushion rubber goes up and down when turned.
(c) Adjust the hood lock.
(1) Remove the front bumper cover (See page
B68579 76-2 ).
(2) Using a screwdriver, disengage the 4 claws and re-
move the hood lock release lever protector.
HINT:
Tape the screwdriver tip before use.
NOTICE:
Removing the protector damages the clips inside the pro-
tector. Therefore, the use of a new protector is necessary
Clip for installation.
B67479
(3) Loosen the 3 hood lock mounting bolts.
(4) Adjust the striker position by moving the hood lock,
so that the striker can enter smoothly.
(5) Tighten the hood lock bolts after the adjustment.
Torque: 8.0 Nm (82 kgfcm, 71 in.lbf)
B67480
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3364
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo