Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 33 20y2n x140001
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download x140001 documenatation <<
Text preview - extract from the document
69-6
COMMUNICATION SYSTEM - GARAGE DOOR OPENER SYSTEM
GARAGE DOOR OPENER SYSTEM
6907N-01
REGISTRATION
1. RESISTER TRANSMITTER CODE
HINT:
The garage door opener is built in the dome lamp assy No.1. When transmitter codes for garage door, gate,
entry gate, door lock, home lighting system or security system are registered with the garage door opener,
be sure to register them again whenever replacing the dome lamp assy No.1.
(a) After the dome lamp assy No.1 has been replaced, register transmitter codes with the garage door
opener (Registration mode).
NOTICE:
S While the transmitter code for a system (garage, door, gate, etc.) is being registered, the system
may operate. During code registration and while the system is in operation, be sure that no
people or objects are in the way.
S Be sure to stop the engine and remove the key from the ignition switch before transmitter code
registration.
S The garage door opener does not apply to systems manufactured before April 1, 1982 and sys-
tems that do not comply with the Federal Safety Standards.
S Garage doors without a jam protection function do not meet the Federal Safety Standards.
HINT:
S Every one of the garage door opener switches can have only one transmitter code; total 3 transmitter
codes can be registered with the garage door opener.
S Even if the battery is disconnected, transmitter codes registered with the garage door opener will not
be erased.
S Even if you attempt to rewrite the transmitter code registered with the garage door opener and the at-
tempt has failed, the registered transmitter code will not be erased.
Garage Door Opener These (1) Select a switch of the garage door opener for trans-
Switches mitter code registration.
(2) Press and hold the selected switch for 20 seconds.
Then, the garage door opener enters registration
mode.
HINT:
Indicator When the garage door opener is in registration mode, the LED
changes from ON to flashing at a cycle of 1 Hz. (In the case of
B70010 the "rolling code" type, the garage door indicator will flash at a
cycle of 8.8 Hz for 1.6 seconds at first and then change the flash
cycle to 1 Hz after the garage door opener has entered registra-
tion mode.)
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3176
69-7
COMMUNICATION SYSTEM - GARAGE DOOR OPENER SYSTEM
Garage Door Opener (3) After the garage door opener has entered registra-
Original tion mode, bring the original transmitter of the sys-
Transmitter tem within 1-inch of the garage door opener while
pressing the switch of the garage door opener. Un-
der this condition, press the original transmitter.
(4) When the transmitter code registration has been
completed correctly, the indicator of the garage
Press door opener flashes at a cycle of 5.6 Hz. When this
B70011 happens, release both the switch and the original
transmitter.
HINT:
S If the code registration has failed, the battery of the original transmitter may be weak or the system may
not meet the garage door opener. In this case, press the original transmitter repeatedly. Some trans-
mitters may need 1 to 2 seconds to stop transmitting signals.
S If the transmitter code registration has not been completed in 90 seconds after the garage door opener
has entered registration mode, the garage door opener will enter low power mode (See step c).
Timing Chart of Registration Mode:
PRESSED
Garage Door
Opener Switch
RELEASED
Registrat ion ENTER 20 sec.
Mode
EXIT
ON
INDICATOR
Operation
OFF
INDICATOR flashes
at a cycle of 1 Hz
INDICATOR flashes
at a cycle of 5.6 Hz
Original ON
Transmitter
OFF
I03487
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3177
69-8
COMMUNICATION SYSTEM - GARAGE DOOR OPENER SYSTEM
Garage Door Opener These (b) Erase the transmitter codes (Clear mode).
Switches HINT:
S All the transmitter codes registered in the garage door
opener are erased at the same time (maximum 3 codes).
S If the switches are released within 10 seconds after the
transmitter codes have been erased, the garage door
Indicator opener will enter registration mode.
S If the switches are held for 10 seconds or more after the
B70010 transmitter codes have been erased, default codes will be
set to all the 3 switches of the garage door opener. With
this default code, you can check operation of the garage
door opener using a tester.
(1) Press and hold the 2 switches at both ends of the
garage door opener simultaneously for 20 seconds.
Then, the indicator starts flashing at a cycle of 5.6
Hz. Releasing the switches will end clear mode.
Timing Chart of Clear Mode:
Garage Door PRESSED
Opener Switches Enter clear mode to erase
(at both ends) RELEASED all 3 codes
Load Default Code
ON
Clear Mode/Default Mode 20 sec. 10 sec.
OFF
ON
INDICATOR
Operation OFF
INDICATOR flashes at a cycle of 5.6 Hz
A53171
(c) Low power mode:
(1) If the switch of the garage door opener is held for 75 seconds or more, the garage door opener
will enter low power mode to economize the power consumption. When the garage door opener
has entered low power mode, the indicator goes off.
2005 SIENNA REPAIR MANUAL (RM1163U)
Author : Date : 3178
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo