Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Sienna 2004-2007 Approved SRM 45 05sie0 dynamicl
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download dynamicl documenatation <<
Text preview - extract from the document
SIENNA (QRG_U)
This quick reference guide provides you with information on Dynamic Laser Cruise Control
Vehicle- to- Vehicle Distance Control Mode. Prior to use of this system, you should be thoroughly familiar
with this system, referring to "Dynamic Laser Cruise Control" in Section 1- 7, Owner's Manual in
conjunction with this quick reference guide.
J Dynamic Laser Cruise Control Operation
The laser radar sensor in this system primarily detects the reflectors of the vehicle ahead of you to determine the presence of the
vehicle and the vehicle- to- vehicle distance. The detection range of the sensor is about 120 m (400 ft.) ahead.
F If no vehicle is detected ahead of you:
D Your cruising speed is maintained at the preset speed from about 45 km/h (28 mph) to about 135 km/h (85 mph).
F If a vehicle is detected ahead of you:
D Your cruising speed changes in proportion to the speed of the vehicle ahead to maintain an appropriate distance from your vehicle
to the vehicle ahead.
D If the vehicle ahead is out of the detection range, your cruising speed will be gradually increased up to the preset speed, and your
vehicle resumes fixed- speed cruising.
D If the vehicle ahead decelerates abruptly or other vehicles cut in ahead of you, your vehicle may be too close to the vehicle ahead
of you. If this occurs, the display flashes and beeps. (Approach warning)
The dynamic laser cruise control should be used on roads in which sufficient vehicle- to- vehicle distance will be ensured
(such as on freeways).
-1-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
J Operation Requirements
Cruising from about 45 km/h (28 mph) to about 135 km/h (85 mph)
y16058q The wipers are not operating at all or operating
intermittently (including the same wiper operation
in the "AUTO" position).
The selector lever is in the "D" position.
Even if these requirements are met, the system may not
operate properly under certain conditions such as bad
weather. See "Owner's Manual" for details.
See Owner's Manual for Complete Information.
-2-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
J Cautions
F Do not rely too much on dynamic laser cruise control. Vehicle- to- vehicle distance control has its limitations.
Always remain aware of the distance from the vehicle ahead and other vehicles. If necessary, depress the brake pedal to
ensure sufficient distance.
F Dynamic laser cruise control is not a collision- avoidance system.
If necessary, depress the brake pedal to ensure sufficient distance.
F Dynamic laser cruise control should not be used in the following conditions:
D In bad weather (such as rain, fog, snow, sandstorms) y16078
D In direct sunlight from the front
D Raindrops or snowflakes get in the laser radar sensor glass
D On the roads in heavy traffic or at sharp bends
D On slippery road surfaces (icy or snow- covered road surfaces)
D On steep downhill slopes
D Continual acceleration or deceleration (such as on busy traffic)
D On roads with steep and short inclines and declines
In any conditions of the above, an appropriate vehicle- to- vehicle distance control
may not be attained.
F This system is not provided to justify careless driving.
Always remain aware of the distance from the vehicle ahead and other vehicles.
F The dynamic laser cruise control should not be used when exiting from,
or when entering or merging onto a freeway.
When you are following a slower moving vehicle and exiting, the sensor
does not detect the vehicle and will accelerate to preset speed.
y16079q
-3-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
J Cautions
F If other vehicles are driving outside of the laser radar detection range, a delay in the detection of the vehicle cutting in
at short range or detection failure of the motorcycle running on the side of the same lane will occur. In this case, the
dynamic laser cruise control system will not function properly.
F The distance between your vehicle and the vehicle ahead cannot be accurately detected in the following cases:
D The vehicle ahead has higher ground clearance, which means that the placement of the reflectors is in a higher position.
D The rear section of the vehicle ahead is extremely dirty.
D The vehicle ahead or other vehicles around you are flinging up water or snow.
D Excessive exhaust gas (black smoke) is coming from the vehicle ahead or other vehicles around you, obscuring your front
view.
D Protective film is attached to the reflectors on the vehicle ahead, or reflectors are not installed on the vehicle ahead or are
damaged.
D Heavy luggage is loaded on top of your rear seats.
F The laser radar sensor automatically detects dirt if dirt is sticking to the sensor glass of your vehicle.
However, in some cases dirt may not be detected. At this time warning display does not operate and an appropriate
vehicle- to- vehicle distance cannot be maintained. Continue driving with due care to the vehicle ahead.
F Dynamic laser cruise control does not operate when the vehicle is at a stop or is driving very slowly.
D Pay special attention to the very slow vehicle at the end of the line in heavy traffic or at the toll gate.
F Turn off the main switch when dynamic laser cruise control is not in use.
F The approach warning may not turn on even if the vehicle drives closer to the vehicle ahead in the following conditions:
D Your vehicle and the vehicle ahead are cruising at almost the same speed.
D The vehicle ahead is cruising at a faster speed than yours. (The distance between the vehicles will become longer.)
D The accelerator pedal is depressed, immediately after the release of the accelerator pedal or immediately after the speed
setting.
F Depending on the road configuration (curved roads) or your vehicle condition (steering wheel maneuvering, position in
the lane), vehicles in other lanes or surrounding objects will be detected.
See Owner's Manual for Complete Information.
-4-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
J Warning Display
If dynamic laser cruise control detects bad weather or malfunction of the system, the master warning light comes on and the alarm
sounds, and one of the warning codes "E1", "E2" or "E3" will appear on the display.
Warning code Conditions
Master Warning "CRUISE" E1 Laser radar sensor glass is dirty
Light indicator light
D Wipers are operating at high or low speeds
y16061q E2
D Direct sunlight from front
D It is difficult to make a measurement
because of bad weather
Warning code E3 System malfunction has been detected
: "CRUISE" indicator light also flashes.
If a warning message appears on the display, take the appropriate measure referring to Section 1- 7, "Owner's Manual".
J Approach Warning
Dynamic laser cruise control and approach warning do not operate when the vehicle ahead is
at a stop or is driving much slower than your vehicle. Use caution for the vehicle at the end
of the line in heavy traffic or at the tollgate, the vehicle at a stop and the very slow vehicle.
If your vehicle approaches the vehicle ahead because of insufficient braking when the vehicle ahead y16062q
decelerates abruptly or when another vehicle cuts in ahead of you, the display flashes and beeps.
Depress the brake pedal to slow down, ensuring sufficient vehicle- to- vehicle distance.
-5-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
J Operation Procedure
The operation procedure is shown as follows. For the detailed information, see Section 1- 7 in the "Owner's Manual".
F Setting
1 Push the main switch ("ON- OFF" button) to turn on the system. The "CRUISE" and "READY" indicator lights in the instrument
cluster come on.
y16100q y16101q
2 Bring your vehicle to the desired speed.
3 Press the control lever downward in the "- SET" direction and release it. This sets the vehicle at that speed.
If a vehicle is detected ahead of you: Your cruising speed changes in proportion to the speed of the vehicle ahead to maintain an
appropriate distance from your vehicle to the vehicle ahead.
If there was no vehicle ahead, your cruising speed will be gradually increased up to the preset speed.
If no vehicle is detected ahead of you: Your cruising speed is maintained at the preset speed.
F Cancelling
To stop the operation: Push the main switch to turn off.
To stop the operation temporarily:
Pull the control lever in the "CANCEL" direction.
To resume follow- up cruising or cruising at fixed speed, y16102q y16103q
press the control lever upward and release it.
See Owner's Manual for Complete Information.
-6-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
J Operation Procedure
F Acceleration/Deceleration
To accelerate: Depress the accelerator pedal. (When you release the accelerator pedal, follow- up cruising or fixed speed
cruising resumes.) If there was no vehicle ahead, the vehicle will accelerate gradually to the preset speed. At this time,
depressing the accelerator pedal or pressing the control lever upward and releasing it will accelerate quickly.
To decelerate: Depress the brake pedal. (Even when you release the brake pedal, dynamic laser cruise control does not return
to follow- up cruising or fixed speed cruising. Press the control lever upward to resume follow- up- cruising or fixed speed
cruising.)
F Changing the preset speed
Using the control lever: To increase
the preset speed
1 Press the control lever upward or downward.
D Press the control lever upward in the "+ RES" direction to increase the preset speed.
D Press the control lever downward in the "- SET" direction to decrease the preset
y16104q
speed. To decrease
The displayed speed will increase or decrease every 5 mph (for the U.S.A.) or the preset speed
5 km/h (for Canada and Mexico).
2 Release the control lever when the display shows the desired preset speed.
Using the accelerator and brake pedals:
1 Depress the accelerator or brake pedal to attain the desired speed.
2 Press the control lever downward in the "- SET" direction and release the lever. y16101q
-7-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
J Operation Procedure
F To restore the previous control
If the preset speed has been cancelled, when you press the lever upward in the "+ RES" direction while "READY" shows up on
the instrument cluster and at a vehicle speed of about more than 40 km/h (25 mph), the speed set prior to cancellation will be
restored.
y16068q
F Changing vehicle- to- vehicle distance setting
You can select one of the following vehicle- to- vehicle distances: LONG, MIDDLE or SHORT. Each time you push the distance
switch briefly, the setting changes from LONG to MIDDLE to SHORT and then back to LONG. You can confirm the setting on
the display.
LONG MIDDLE SHORT
y16069q
y16070q y16071q y16072q
See Owner's Manual for Complete Information.
-8-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
SIENNA (QRG_U)
In addition to the vehicle- to- vehicle distance control mode described in this quick reference guide, dynamic laser cruise
control has conventional (fixed speed) cruise control mode for cruising at fixed speeds. For the conventional (fixed speed)
cruise control mode, see Section 1- 7 in the "Owner's Manual".
F Changing to the conventional (fixed speed) control mode F Each mode display
1 Push the main switch ("ON- OFF" button) to turn on the The control system in the vehicle- to- vehicle distance control
system. The "CRUISE" and "READY" indicator lights in the mode differs from the one in the conventional (fixed speed)
instrument cluster come on. cruise control mode.
When using dynamic laser cruise control, make sure which
mode is selected.
y16100q Displays in the instrument cluster:
Vehicle- to- Vehicle Distance
Fixed Speed Control Mode
Control Mode
2 Push the control lever in the "MODE" direction for longer
In Ready State
than 1 second to change to conventional cruise control
mode. The "NORM." indicator light in the instrument y16075q
cluster comes on. y16068q y16068q
y16105q
In Control
y16076q y16077q
-9-
2005 SIENNA QRG from Sep. '04 Prod. (OM45430U)
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo