Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra bo bwg remo
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download remo documenatation <<
Text preview - extract from the document
BO-85
BODY - BACK WINDOW GLASS
BO4Q5-01
REMOVAL
HINT:
A bolt without a torque specification is shown in the standard
bolt chart (see page SS-2).
1. Access cab (Standard body type):
Access cab (Wide body type):
REMOVE REAR SEAT (See page BO-203)
2. Double cab:
FOLD REAR SEAT
(b) (a) Lower the headrest to the lowest position. Pull the seat-
back angle adjusting lever and fold the seatback down.
(b) Unlock the seat legs by pulling up one of the lever on the
seat legs and turn up the whole seat forward.
3. Standard cab:
(a) REMOVE FRONT DOOR SCUFF PLATES
H23147 (see page BO-126)
4. Access cab (Standard body type):
Access cab (Wide body type):
REMOVE ACCESS DOOR SCUFF PLATES
(See page BO-126)
5. Double cab:
REMOVE BACK PANEL TRIM (See page BO-133)
6. REMOVE ASSIST GRIPS
(See page BO-126, BO-133)
7. Standard cab:
REMOVE FRONT PILLAR GARNISHES
(See page BO-126)
8. Access cab (Standard body type):
Access cab (Wide body type):
REMOVE ROOF SIDE RAIL GARNISHES
(See page BO-126)
9. REMOVE ROOM LIGHT (See page BO-126, BO-133)
10. Standard cab:
REMOVE COAT HOOK (See page BO-126)
11. Standard cab:
REMOVE BACK PANEL UPPER GARNISH
(See page BO-126)
12. Access cab (Standard body type):
Access cab (Wide body type):
REMOVE QUARTER TRIMS (See page BO-126)
13. Double cab:
REMOVE QUARTER TRIMS LOWER
(See page BO-133)
14. Double cab:
REMOVE QUARTER TRIMS UPPER
(See page BO-133)
BO-86
BODY - BACK WINDOW GLASS
15. Standard cab:
Access cab (Standard body type):
Access cab (Wide body type):
REMOVE REAR PART OF ROOF HEADLINING
(a) Standard cab:
Remove the 2 clips and the rear part of the roof headlin-
ing.
(b) Access cab (Standard body type):
Access cab (Wide body type):
Remove the 3 clips and the rear part of the roof headlin-
ing.
16. Power slide type:
REMOVE BACK WINDOW REGULATOR ASSEMBLY
(a) Remove the 2 bolts and tether anchor brackets.
(b) Remove the 4 clips and 2 back panel silencer pads.
H20704
(c) Using a screwdriver, remove the back door glass channel
cover.
HINT:
Tape the screwdriver tip before use.
H20706
(d) Remove the 7 nuts and the back window regulator as-
sembly.
H20705
BO-87
BODY - BACK WINDOW GLASS
17. Power vertical type:
REMOVE SERVICE HOLE COVER
(a) Remove the 12 bolts.
H22882
(b) Using a clip remover, remove the 2 clips and cover.
NOTICE:
When the clips are removed, the cover may fall and become
deformed.
Cover
H23130
18. Power vertical type:
REMOVE WEATHERSTRIP OUTER
(a) Put protective tape under the weatherstrip.
(b) Using a screwdriver, disengage the claws and remove the
weatherstrip.
HINT:
Tape the screwdriver tip before use.
H22886
19. Power vertical type:
REMOVE WEATHERSTRIP INNER
Using a screwdriver, remove the weatherstrip.
H23237
BO-88
BODY - BACK WINDOW GLASS
20. Power vertical type:
REMOVE BACK WINDOW GLASS
(a) Disconnect the defogger connector.
(b) Remove the 4 bolts and glass.
HINT:
Insert a shop rag inside the panel to prevent the back window
glass from being scratched.
NOTICE:
S Do not damage the back window glass assembly.
S When the bolts are removed, the back window glass
assembly might fall and become deformed.
H22885
21. Power vertical type:
REMOVE BACK WINDOW REGULATOR ASSEMBLY
(a) Disconnect the connector.
(b) Remove the 7 bolts and regulator.
HINT:
Remove the back window regulator assembly through the ser-
vice hole.
NOTICE:
Connector H22884 When the bolts are removed, the back window regulator as-
sembly may fall and become deformed.
22. Power vertical type:
REMOVE BACK WINDOW MOULDING
(a) Remove the 8 bolts and the bracket LH and RH.
H22883
(b) Remove the 2 clips.
(c) Using a drill of less than ◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo