Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra bo frosease disa
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download disa documenatation <<
Text preview - extract from the document
BO-142
BODY - FRONT SEAT (Separate Type: Power Adjuster)
BO4S8-02
DISASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:
S Tape the screwdriver tip before using it to remove the
parts.
S For easy removal of the lumbar support adjuster, release
the lumbar support through lumbar switch operation.
1. REMOVE HEADREST
2. REMOVE SLIDE KNOB AND RECLINING KNOB
Using a screwdriver, remove the slide knob and reclining knob.
HINT:
Tape the screwdriver tip before use.
H24311
3. REMOVE SEAT CUSHION LOWER SHIELD, SEAT
CUSHION OUTER SHIELD AND SEAT CUSHION IN-
NER SHIELD
(a) Remove the screw from the seat cushion outer shield.
(b) Perform the same procedure on the seat cushion inner
shield.
H24312
(c) Remove the 2 screws from the seat cushion outer shield.
(d) Remove the screw from the seat cushion inner shield.
H24313
BO-143
BODY - FRONT SEAT (Separate Type: Power Adjuster)
(e) Remove the 2 screws from the seat cushion lower shield.
(f) Disconnect the lumbar switch connector from the seat
cushion outer shield, and remove the seat cushion lower
shield, outer shield and inner shield.
H24314
(g) Remove the screw and separate the seat cushion lower
shield and seat cushion outer shield.
(h) Perform the same procedure on the other side.
4. REMOVE FRONT SEAT INNER BELT
(a) Disconnect the wire harness clamps and connectors.
(b) Remove the nut and front seat inner belt.
5. REMOVE LUMBAR SWITCH
Remove the 2 screws and lumbar switch from the seat cushion
H24315 outer shield.
6. REMOVE POWER SEAT SWITCH
Remove the 3 screws and power seat switch.
7. REMOVE ARMREST ASSEMBLY
(a) Using a screwdriver, remove the armrest cap.
(b) Remove the bolt, armrest spacer, armrest lock plate and
armrest assembly.
(c) Remove the spacer from the armrest assembly.
H24316
8. REMOVE SEATBACK COVER AND PAD
(a) Remove the hog rings from the seat frame assembly.
(b) Open the fastener.
H24317
BO-144
BODY - FRONT SEAT (Separate Type: Power Adjuster)
(c) w/ Side airbag:
Remove the nut and disconnect the seatback cover
bracket from the seat frame assembly.
H24861
(d) Remove the hog rings from the seat frame assembly.
Hog Ring
H24321
(e) Remove the hog rings from the seat frame assembly.
(f) Remove the seatback cover and pad from the seat frame
assembly.
Hog Ring H24318
9. REMOVE SEATBACK COVER
(a) Turn up the seatback cover and remove the hog rings.
(b) Remove the 2 headrest supports.
(c) Remove the seatback cover from the seatback pad.
10. w/ Seat heater:
REMOVE SEATBACK HEATER ASSEMBLY
Cut off the tack pins which fasten the seat heater, and then re-
move the seatback heater assembly from the seatback cover.
H24319 11. REMOVE SEAT CUSHION COVER AND PAD
(a) Disconnect the wire harness clamp.
(b) Remove the 2 clips.
H24320
BO-145
BODY - FRONT SEAT (Separate Type: Power Adjuster)
(c) Remove the hog rings from the seat cushion cover.
(d) Unlatch the seat cushion cover hooks, then remove the
seat cushion cover and seat cushion pad.
H24378
12. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat
cushion pad.
13. w/ Seat heater:
REMOVE SEAT CUSHION HEATER ASSEMBLY
Cut off the tack pins which fasten the seat heater, and then re-
move the seat cushion heater assembly from the seat cushion
cover.
H24395
14. REMOVE LUMBAR SUPPORT ADJUSTER
(a) Disconnect the connector.
(b) Disengage the seatback spring edge from the seat frame
assembly.
NOTICE:
Be careful when releasing the seatback spring edge, be-
cause there is a possibility that the spring may break due
to tension by the lumbar support.
H24324
(c) Remove the 2 screws and lumbar support adjuster.
(d) Remove the bushing from the lumbar support adjuster.
H24325
15. REMOVE RH AND LH RECLINING ADJUSTER INSIDE
COVERS
(a) Remove the screw and RH reclining adjuster inside cover.
(b) Disconnect the wire harness clamp.
(c) Perform the same procedure on the other side.
H24326
BO-146
BODY - FRONT SEAT (Separate Type: Power Adjuster)
16. REMOVE RH AND LH SEATBACK SHIELDS
(a) Remove the 2 screws and RH seatback shield.
(b) Perform the same procedure on the other side.
17. REMOVE VERTICAL ADJUSTER BRACKET INNER
AND OUTER COVERS
(a) Remove the screw and vertical adjuster bracket inner
cover.
(b) Perform the same procedure on the other side.
H24327 18. REMOVE SEAT POSITION SENSOR
(See page RS-118)
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo