Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra be comp1dou cali
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download cali documenatation <<
Text preview - extract from the document
BE-99
BODY ELECTRICAL - COMPASS (Double Cab)
BE2MF-01
CALIBRATION
1. SELECTING COMPASS DISPLAY MODE
The mode select switch allows you to select the Display or Non-display mode of the compass.
2. SETTING ZONE
Deviation between the "magnetic north" and "actual north" differs depending on the terrestrial location.
Therefore, adjustment of the magnetism is required. Since the magnetic condition differs depending on the
area where the vehicle is used, it is necessary for each user to set the zone. (Refer to Compass Zone Map).
The zone setting can be changed using the E/M switch of the display.
3. PERFORMING CALIBRATION
Because each vehicle has its own magnetic field, calibration should be performed for each vehicle. This com-
pass function is used when storing the record of the vehicle's magnetic field.
4. WHEN COMPASS MAGNETIZED:
A compass could be magnetized during shipping by vessels or freight cars. Therefore, make sure to perform
calibration and ensure that calibration is performed properly before delivery. If it cannot be done (cannot
complete in spite of driving round several times), it may be caused by magnetization. Demagnetize the ve-
hicle using a demagnetizer and perform calibration again.
5. SETTING COMPASS
Press E/M and MODE Switches
at the same time. On Duration
Normal Mode
Ignition switch ON.
Pressed for 5 sec.
6. Zone Setting Mode
Pressed for 10 sec.
E/M Switch ON
Zone area +1
7. Calibration Mode
Leaving it untouched
for a while
Normal Mode
BE-100
BODY ELECTRICAL - COMPASS (Double Cab)
6. ZONE SETTING MODE
(a) Turn the ignition switch ON.
(b) To keep pressing the E/M switch and MODE switch for 5 seconds when outer temperature is displayed
will activate the zone setting mode. A number (1 to 15) is displayed on the compass display.
I27615
BE-101
BODY ELECTRICAL - COMPASS (Double Cab)
HINT:
In the initial status, "8" is displayed.
(c) The displayed number increases +1 every time the E/M switch is pressed. Referring to the map, check
the number for the area where the vehicle will be used and set the zone number.
(d) Leave it untouched for several seconds after setting and check that the compass display shows an
azimuthal direction (N, NE, E, SE, S, SW, W, or NW) or "VAR".
7. CALIBRATION SETTING MODE
(a) After the set zone is displayed, if the E/M switch and MODE switch remains pressed another 5 seconds
will activate the calibration setting mode.
(b) To keep pressing the E/M switch and MODE switch for 10 seconds when outer temperature is dis-
played will also activate this mode.
(c) Drive the vehicle at a slow speed of 8 km/h (5 mph) or less in the circular direction.
(d) Driving round the circle 1 to 3 times will display the azimuthal direction on the display, completing the
calibration.
HINT:
After the calibration is completed, it is not necessary to perform the above procedures unless the magnetic
field strength is drastically changed. If this happens, the azimuthal display will be changed to "CAL".
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo