Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra be bpwsydou insp

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.




Image preview - the first page of the document
insp


>> Download insp documenatation <<

Text preview - extract from the document
                                                                                                                            BE-119
                                      BODY ELECTRICAL         -     BACK POWER WINDOW SYSTEM (Double Cab)
                                                                                                                                 BE2LY-02


                                                  INSPECTION
                                                  1.       INSPECT BACK POWER WINDOW SWITCH CONTI-
                                                           NUITY
                                                          Switch Position        Tester Connection            Specified Condition
                                                               UP                   1 - 3, 2 - 6                    Continuity
                                                               OFF                  2 - 3, 2 - 6                 No continuity
                                                             DOWN                   1 - 6, 2 - 3                    Continuity
                           No Pin                 If the continuity is not as specified, replace the switch.
                                         I27173




Wire harness side                                 2.       CHECK BACK WINDOW CONTROL RELAY CIRCUIT
                                                  (a)      Disconnect the connector from the relay, and check the
                                                           connector on the wire harness side, as shown in the table
                                                           below.




                                         I27437




       Tester Connection                                Condition                                  Specified Condition
        6 - Body ground             Ignition switch OFF or ACC  ON                                 0 V  10 to 14 V
        8 - Body ground             Limit switch OFF  ON                                    10 k or higher  Below 1 
        9 - Body ground             Constant                                                           Continuity
       11 - Body ground             Constant                                                           Continuity
       12 - Body ground             Ignition switch OFF or ACC  ON                                 0 V  10 to 14 V
                                                  If the result is not as specified, there may be a malfunction on
                                                  the wire harness side or limit switch.
                                                  (b) Reconnect the connector to the relay, and check the con-
                                                         nector on the wire harness side, as shown in the table be-
                                                         low.
       Tester Connection                                Condition                                  Specified Condition
                                    S Ignition switch ON
                                    S Power back window fully open
        4 - Body ground                                                                            0 V  10 to 14 V
                                    S Limit switch OFF
                                    S Switch not pressed (OFF)  Pressed (UP)

                                    S Ignition switch ON
        5 - Body ground             S Power back window fully closed                               0 V  10 to 14 V
                                    S Switch not pressed (OFF)  Pressed (DOWN)
                                                  If the result is not as specified, replace the relay.
BE-120
                        BODY ELECTRICAL         -   BACK POWER WINDOW SYSTEM (Double Cab)

                                     3.     CHECK BACK POWER WINDOW MOTOR PTC
 4             1   4     1                  THERMISTOR OPERATION
                                     (a)    Disconnect the connector from the window motor.
                                     (b)    Connect the positive (+) lead from the ammeter to termi-
                                            nal 1 of the wire harness side connector and the negative
                                            (-) lead to the negative terminal of the battery.
                                     (c)    Connect the positive (+) lead from the battery to terminal
                                            2 of the wire harness side connector, and slide the window
                            I27478          to the fully closed position.

                                     (d)   Continue to apply voltage and check that the current
 4             1   4    1                  changes to less than 1 A in 4 to 90 seconds.
                                     (e) Disconnect the leads from the terminals.
                                     (f)   Approximately 60 seconds later, connect the positive (+)
                                           lead from the battery to terminal 1 and the negative (-)
                                           lead to terminal 2, and check that the window begins to
                                           moves down.
                                     If operation is not as specified, replace the power back window
                            I27479   regulator and motor assembly.

                                     4.     INSPECT POWER MAIN RELAY CONTINUITY
           2                                    Tester Connection                       Specified Condition
1
                                                       3-5                                No Continuity
                   3         5
                                                                                            Continuity
           5                                           3-5                       (When battery voltage is applied
                   1         2                                                        to terminals 1 and 2)
 3
                                     If the continuity is not as specified, replace the relay.

                         N14863



                                     5.     INSPECT BACK WINDOW RELAY CONTINUITY
           2                                    Tester Connection                       Specified Condition
1
                                                       3-5                                No Continuity
                   3         5
                                                                                            Continuity
           5                                           3-5                       (When battery voltage is applied
                   1         2                                                        to terminals 1 and 2)
 3
                                     If the continuity is not as specified, replace the relay.

                         N14863




Released
                                     6.     INSPECT WINDOW LIMIT SWITCH CONTINUITY
               Pushed
                                           Switch position          Tester Connection          Specified Condition
                                           Lever pushed                   1-2                     No continuity
                                           Lever released                 1-2                      Continuity
                                     If the continuity is not as specified, replace the power back win-
                                     dow regulator and motor assembly.


                   1    2
                            I27616



◦ Jabse Service Manual Search 2026 ◦ Jabse PravopisonTap.bg ◦ Other service manual resources online : FixyaeServiceinfo