Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra be pwcsydou insp
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download insp documenatation <<
Text preview - extract from the document
BE-109
BODY ELECTRICAL - POWER WINDOW CONTROL SYSTEM (Double Cab)
BE2LF-02
INSPECTION
1. INSPECT POWER WINDOW REGULATOR SWITCH
CONTINUITY
Switch Position Tester Connection Specified Condition
UP 2 - 3, 4 - 5 Continuity
OFF 2-3-5 Continuity
DOWN 2 - 4, 3 - 5 Continuity
I08152 If the continuity is not as specified, replace the switch.
2. INSPECT POWER MAIN RELAY CONTINUITY
2 Tester Connection Specified Condition
1
3-5 No continuity
3 5
Continuity
3-5
5 (When battery voltage is applied to terminals 1 and 2)
1 2
If the continuity is not as specified, replace the relay.
3
N14863
3. Driver side door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2, and check that
the motor turns clockwise.
2 1 I15351
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
2 1 I15352
4. Passenger side door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (-) lead to terminal 1, and check that
the motor turns clockwise.
2 1 I27631
BE-110
BODY ELECTRICAL - POWER WINDOW CONTROL SYSTEM (Double Cab)
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
2 1 I27630
5. Rear right door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminals 2, then check that
the motor turns clockwise.
2 1
I27178
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
2 1
I27179
6. Rear left door:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
2 and the negative (-) lead to terminal 1, then check that
the motor turns clockwise.
2 1
I27181
(b) Reverse the polarity and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
2 1
I27180
BE-111
BODY ELECTRICAL - POWER WINDOW CONTROL SYSTEM (Double Cab)
7. Driver side door:
INSPECT POWER WINDOW MOTOR PTC THERM-
ISTOR OPERATION
(a) Disconnect the connector from the motor.
1 (b) Connect the positive (+) lead from the ammeter to termi-
nal 1 of the motor side connector and the negative (-) lead
to negative terminal of the battery.
2 (c) Connect the positive (+) lead from the battery to terminal
I27172 2 of the motor side connector, and raise the window to the
fully closed position.
(d) Continue to apply voltage and check that the current
changes from approximately 14 A to less than 1 A within
4 to 90 seconds.
(e) Disconnect the leads from the terminals.
(f) Approximately 90 seconds later, connect the positive (+)
lead from the battery to terminal 1 and the negative (-)
lead to terminal 2, then check that the window begins to
move down.
2 1
I14318 If operation is not as specified, replace the motor.
1
8. Passenger side door:
2
INSPECT POWER WINDOW MOTOR PTC THERM-
ISTOR OPERATION
(a) Disconnect the connector from the motor.
(b) Connect the positive (+) lead from the ammeter to termi-
nal 2 of the motor connector and the negative (-) lead to
negative terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal
I21325 1 of the motor connector, and raise the window to the fully
closed position.
(d) Continue to apply voltage and check that the current
changes from approximately 14 A to less than 1 A within
4 to 90 seconds.
(e) Disconnect the leads from the terminals.
(f) Approximately 90 seconds later, connect the positive (+)
lead from the battery to terminal 2 and the negative (-)
lead to terminal 1, then check that the window begins to
move down.
2 1 I21327 If operation is not as specified, replace the motor.
9. Rear left door:
2
INSPECT POWER WINDOW MOTOR PTC THERM-
ISTOR OPERATION
(a) Disconnect the connector from the motor.
(b) Connect the negative (+) lead from the ammeter to termi-
1 nal 1 of the motor connector and the negative (-) lead to
negative terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal
I27174 2 of the motor connector, and raise the window to the fully
closed position.
BE-112
BODY ELECTRICAL - POWER WINDOW CONTROL SYSTEM (Double Cab)
(d) Continue to apply voltage and check that the current
2 1 changes from approximately 14 A to less than 1 A within
4 to 90 seconds.
(e) Disconnect the leads from the terminals.
(f) Approximately 90 seconds later, connect the positive (+)
lead from the battery to terminal 1 and the negative (-)
lead to terminal 2, then check that the window begins to
move down.
I27175 If operation is not as specified, replace the motor.
10. Rear right door:
2 1 INSPECT POWER WINDOW MOTOR PTC THERM-
ISTOR OPERATION
(a) Disconnect the connector from the motor.
(b) Connect the negative (+) lead from the ammeter to termi-
nal 2 of the motor connector and the negative (-) lead to
negative terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal
I27176 1 of the motor connector, and raise the window to the fully
closed position.
(d) Continue to apply voltage and check that the current
2 1 changes from approximately 14 A to less than 1 A within
4 to 90 seconds.
(e) Disconnect the leads from the terminals.
(f) Approximately 90 seconds later, connect the positive (+)
lead from the battery to terminal 2 and the negative (-)
lead to terminal 1, check that the window begins to move
down.
I27177 If operation is not as specified, replace the motor.
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo