Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra be wawsy insp
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download insp documenatation <<
Text preview - extract from the document
BE-76
BODY ELECTRICAL - WIPER AND WASHER SYSTEM
BE179-04
w/ Mist
MIST
INSPECTION
1. INSPECT FRONT WIPER AND WASHER SWITCH
OFF
CONTINUITY
LO w/ Mist:
Switch Position Tester Connection Specified Condition
HI
MIST 7 - 17, 16 - 17 Continuity
w/ Intermittent
OFF 7 - 16 Continuity
OFF
LO 7 - 17 Continuity
INT HI 8 - 17 Continuity
Washer ON 2 - 11 Continuity
LO
w/ Intermittent:
HI
Switch Position Tester Connection Specified Condition
OFF 7 - 16 Continuity
INT 7 - 16 Continuity
9 8 7 6 5 4 3 2 1 LO 7 - 17 Continuity
18 17 16 15 14 13 12 11 10 HI 8 - 17 Continuity
Washer ON 2 - 11 Continuity
N18027
If the continuity is not as specified, replace the switch.
2. INSPECT INTERMITTENT OPERATION
(a) Turn the wiper switch to the INT position.
7 2 (b) Turn the intermittent time control switch to the FAST posi-
tion.
(c) Connect the positive (+) lead from the battery to terminal
16 and the negative (-) lead to terminal 2.
16 (d) Connect the positive (+) lead from the voltmeter to termi-
nal 7 and the negative (-) lead to terminal 2, check that
I01313 the meter needle indicates battery positive voltage.
INT time control
switch position
Voltage
Approx. 1 to 3 sec.
FAST Battery positive voltage
0V
Approx. 10 to 15 sec.
SLOW Battery positive voltage
0V
V03883
If the result is not as specified, replace the switch.
BE-77
BODY ELECTRICAL - WIPER AND WASHER SYSTEM
3. INSPECT WASHER LINKED OPERATION
(a) Connect the positive (+) lead from the battery to terminal
7 2 16 and the negative (-) lead to terminal 2.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 7 and the negative (-) lead to terminal 2.
(c) Push in the washer switch, and check that the voltage
16 changes as shown in the table below.
I01313
Washer Switch ON
OFF
Less than 1 sec. Approx. 3 sec.
Battery Voltage
0V
N11301
If the operation is not as specified, replace the wiper and wash-
er switch.
4. Low speed:
INSPECT WIPER MOTOR OPERATION
5
Connect the positive (+) lead from the battery to terminal 5 and
the negative (-) lead from the battery to the motor body or termi-
nal 4, and check that the motor operates at low speed.
If operation is not as specified, replace the motor.
4
I01934
5. High speed:
3 INSPECT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 3 and
the negative (-) lead from the battery to the motor body or termi-
nal 4, and check that the motor operates at high speed.
If operation is not as specified, replace the motor.
4
I01935
6. Stopping at stop position:
5
INSPECT WIPER MOTOR OPERATION
(a) Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing the positive (+) lead from terminal 5.
4
I01936
BE-78
BODY ELECTRICAL - WIPER AND WASHER SYSTEM
1 (b) Connect terminals 1 and 5.
2
(c) Connect the positive (+) lead from the battery to terminal
2 and the negative (-) lead from the battery to the motor
body or terminal 4, and check that the motor stops run-
ning at the stop position after the motor operates again.
5 If operation is not as specified, replace the motor.
4
I01937
7. INSPECT WASHER MOTOR OPERATION
2
Connect the positive (+) lead from the battery to terminal 2 and
the negative (-) lead to terminal 1, and check that the motor op-
erates.
1 NOTICE:
These tests must be performed quickly (within 20 seconds)
to prevent the coil from burning out.
If operation is not as specified, replace the motor.
N13907
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo