Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra be wdlcsdou insp
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download insp documenatation <<
Text preview - extract from the document
BE-166 BODY ELECTRICAL - WIRELESS DOOR LOCK CONTROL SYSTEM (Double
Cab)
BE2LP-01
INSPECTION
1. INSPECT DOOR LOCK TRANSMITTER
(a) Inspect operation of the transmitter.
(1) Remove the battery (lithium battery) from the trans-
mitter (see page BE-168).
(2) Install a new or normal battery (lithium battery).
HINT:
When a new or normal battery is not available, connect 2 new
1.5 V batteries in series, connect the battery's positive (+) to the
battery receptacle side terminal and battery's negative (-) to the
bottom terminal, then apply 3 V of voltage to the transmitter.
(3) In a location that is approx. 1 m (3.28 ft) away from
the driver side outside door handle in the right direc-
tion, point the key plate of the transmitter at the ve-
I21534 hicle and check operation of the transmitter by
pressing the transmission switch on the transmitter
body.
Standard:
The door lock can be operated via the remote control.
HINT:
S The minimum operational distance differs depending on
the operator, the way the transmitter is held and the loca-
tion.
S Since the transmitter uses faint electric waves, the opera-
tional distance might be shortened if noise or strong elec-
tric wave occurs in the area where the frequency is used.
(4) Install the battery (lithium battery).
(b) Inspect the battery capacity.
HINT:
S The capacity of the battery can be determined only when
the battery is installed in the transmitter. For a lithium bat-
tery used in the transmitter, a voltage of more than 2.5 V
is shown on the tester until the energy is completely con-
sumed, while no battery is installed in the transmitter.
Therefore, it is necessary to measure the voltage while
the battery is installed in the transmitter (a resistance of
1.2 k is applied to the battery) when checking the
amount of energy left in the battery.
S If the transmitter is faulty, the amount of energy left in the
battery might not be checked correctly.
(1) Remove the battery (lithium battery) from the trans-
mitter (see page BE-168).
BODY ELECTRICAL - WIRELESS DOOR LOCK CONTROL SYSTEM (Double BE-167
Cab)
Lead Wire (2) Connect the lead wire to the negative (-) terminal of
the transmitter and install the battery.
I27609
(3) Connect the tester positive (+) probe to the positive
(+) battery (lithium battery) and the tester negative
(-) probe to the lead respectively.
(4) Press one of the transmission switches on the
transmitter for approx. 1 second.
(5) Press the transmission switch on the transmitter
again to check the voltage.
Standard: 2.2 V or higher
I27507 HINT:
S When the temperature of the battery is low, the inspection
cannot be made correctly.
When the outcome of the test is less than 2.2 V, conduct
the test again after leaving the battery in a place with a
temperature of 18◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo