Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra be wdlcsexc ovi

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.



Image preview - the first page of the document



>> Download ovi documenatation <<

Text preview - extract from the document

                                     BODY ELECTRICAL    -   WIRELESS DOOR LOCK CONTROL SYSTEM (Except    BE-177
                                                            Double Cab)
                                                                                                            BE2KS-01


ON-VEHICLE INSPECTION
INSPECT WIRELESS DOOR LOCK CONTROL FUNCTIONS
HINT:
 S     The switch described in this text is a switch for transmitting signals which is built into the door control
       transmitter.
 S     All the functions listed below must be checked in the remote control operational area.
(a) Put the vehicle under the conditions that allow the wireless control function to be operated (See PRE-
       CAUTION on page BE-169).
(b) Check the basic function.
       (1) Check whether the LED of the transmitter lights up 3 times when each switch is pressed 3 times.
HINT:
 S     If the LED does not light up when the switch has been pressed 3 times or more, it may be caused by
       the dead battery.
 S     If the switch is held down, the LED blinks continuously.
       (2) Check that all the doors lock when the LOCK switch is pressed.
       (3) Check that all the doors will be unlocked when the UNLOCK switch is pressed.
HINT:
If the double switch operation is set in the setting mode of a transmitter, the unlock operation is not carried
out as specified in step (3) but carried out as follows:
Only the driver's door will be unlocked when the UNLOCK switch is pressed once, and the other door will
be unlocked when the UNLOCK switch is pressed again within 3 seconds.
(c) Check the chattering prevention function.
       Check that the corresponding operation occurs only once and is not repeated continuously while the
       switch is held. However, when the switch is operated repeatedly at 1 second intervals, check that the
       corresponding operation is carried out.
(d) Check the automatic lock function.
       (1) Check that all the doors lock automatically as long as none of them have been opened or all the
              doors have not been locked within approximately 30 seconds after they are unlocked by pressing
              the UNLOCK switch.
       (2) Check that the automatic locking function does not operate when any door has been opened or
              all of them have been locked within approximately 30 seconds after they are unlocked by press-
              ing the UNLOCK switch.
(e) Check the switch operation fail-safe function.
       Check that the doors can not be locked using the switch while the key is in the ignition key cylinder.
       However, this does not apply when the system is in the recognition code registration mode.
(f)    Check the operation stop function when a door is open or not completely closed.
       Check that the doors are not locked by the switch while any door is open or not completely closed.
(g) Check the repeat function.
       Check that all the doors attempt to automatically lock once again in 2 seconds after the LOCK switch
       has been pressed while the movement of the driver side door control knob is being restricted while in
       the unlocked position.
(h) Check the taillights and parking lights flashing and TVIP buzzer chirps functions (answerback).
       (1) When the LOCK switch is pressed, check that the lights flash once and buzzer chirps once with
              the locking of all the doors.
       (2) When the UNLOCK switch is pressed, check that the lights flash twice and buzzer chirp twice
              with the unlocking of all the doors.
BE-178                              BODY ELECTRICAL   -   WIRELESS DOOR LOCK CONTROL SYSTEM (Except
                                                          Double Cab)

(i)   Check the illuminated entry function.
      (1) When all the doors are locked, pressing the UNLOCK switch causes the interior light (when the
            light switch is in the DOOR position) to illuminate simultaneously with the unlock operation.
      (2) Check that the interior light fade out in approximately 30 seconds if doors have not been opened.
(j)   Check the remote panic alarm function.
      Check that the horn sounds and the headlights and taillights flash for 60 seconds by the TVIP alarm
      function when the PANIC switch is pressed. Also, check that the horn stops sounding and the lights
      stop flashing when either switch of the transmitter is pressed or any door is either locked or unlocked
      using the key.
(k)   Check the ignition-controlled automatic door lock/unlock function.
HINT:
This function's initial mode is OFF, however the program for this function can be changed using the specified
method (see page BE-170).
      (1) Insert the key into the ignition key cylinder and turn the ignition switch to on the ON or START
            position. Check that all the doors are automatically locked.
      (2) Turn the key back to the ACC or LOCK position, and check that all the doors automatically un-
            locked.

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo