Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra be theftdou ovi
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download ovi documenatation <<
Text preview - extract from the document
BE-135
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
THEFT DETERRENT SYSTEM (Double Cab)
BE2KX-01
ON-VEHICLE INSPECTION
1. OUTLINE OF THEFT DETERRENT SYSTEM
(a) When the theft deterrent system detects that the vehicle is being tampered with, the system sets off
the alarm, causing the horns to sound and the lights to light up or flash in order to alert people around
the vehicle to the theft.
(b) The theft deterrent system has 2 modes; one is the active arming mode that is an initially set mode
and another is the passive arming mode that can be switched by the hand-held tester.
(c) Each mode (active and passive) has 4 states; the disarmed state, the arming preparation state, the
armed state and the alarm sounding state.
(1) Disarmed state:
S The alarm function is not operating.
S The theft deterrent system is not operating.
(2) Arming preparation state:
S The theft deterrent system is not operating.
(3) Armed state:
S The theft deterrent system is operating.
(4) Alarm sounding state:
When the theft deterrent system detects that the vehicle is being tampered with while in the
armed state, the system causes the horns to sound and the lights to light up or flash in order to
alert people around the vehicle to the theft.
Refer to table below for alarm method and time:
Headlight Flashing at a cycle of approx. 0.4 seconds
Taillight Flashing at a cycle of approx. 0.4 seconds
Alarming method
Interior light Illuminating (turn on)
Vehicle horn Sounding at a cycle of approx. 0.4 seconds
Security horn Sounding at a cycle of approx. 0.4 seconds
Alarming time Approx. 60 seconds
HINT:
If any of the doors are unlocked with no key in the ignition key cylinder during the alarm sounding state, a
forced door lock signal will be output (see step 4).
BE-136
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
2. ACTIVE ARMING MODE
S Active arming mode starts the alarm control immediately after the doors are locked.
Disarmed state
(No key in ignition key cylinder.)
Performing any of the following will cause the system to go into arming preparation state.
D With all doors and engine hood closed, lock all doors by key operation.
D With all doors and engine hood closed, lock all doors by wireless operation.
D With any door or the engine hood open, close all doors and lock all doors and engine hood.
Arming preparation state
Performing any of the following will cause the Performing the following will cause the
system to return to disarmed state. system to go into armed state.
D Unlock any door by wireless operation.
D Unlock any door by key operation. With all doors and engine hood closed,
D Unlock any door. lock all doors. Allow approx. 30 seconds
D Open any door. to elapse.
D Open engine hood.
D Insert key into ignition key cylinder.
D Turn ignition switch from OFF to ON.
D Disconnect battery once, and then reconnect
it.
Continued from next page Continued on next page
BE-137
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
Continued on previous page Continued from
previous page
Armed state
Performing any of the following will Performing any of the follow-
cause the system to return to disarmed ing will cause the system to
state. set off the alarm.
D Unlock any door by wireless opera- D Open engine hood.
tion. D Open any door.
D Unlock any door by key operation. D Unlock any door without key
D Insert key into ignition key cylinder and wireless operation.
and turn ignition switch from OFF to Directly connect ignition
ON. switch without key (or turn
ignition switch ON without
key).
D Disconnect battery once,
and then reconnect it.
Tampering is detected.
Alarm sounding state
Performing any of the following will cause When the system de-
the system to return to disarmed state. tects tampering, the Alarm stops and system
horns sound and returns to armed state.
D Unlock any door by wireless operation. lights illuminate or
D Unlock any door by key operation. flash in order to alert
D Insert key into ignition key cylinder and people around the ve-
turn ignition switch from OFF to ON. hicle to the theft.
After approx. 60 se-
conds, alarm stops
and system returns to
armed state.
Alarm operation is cancelled.
BE-138
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
3. PASSIVE ARMING MODE
S Passive arming mode can be switched ON/OFF by the hand-held tester.
S The alarm is initially set (when shipped from factory) to active arming mode (not passive arming mode).
S During passive arming mode, the theft deterrent system goes into the armed state even if the doors
are not locked.
S Passive arming mode starts the alarm control after the key is removed from the ignition key cylinder
and the doors are closed.
S Detecting that the doors are unlocked does not set off the alarm during passive arming mode.
S A forced door lock signal is not output during passive arming mode (see step 4).
S When the theft deterrent system detects that the doors are opened during passive arming mode, the
alarm is not set off immediately because an entry delay time is set.
S If any of the following conditions is met during passive arming mode, the theft deterrent system will
switch to active arming mode.
S With all doors and engine hood closed, lock all doors by key operation.
S With all doors and engine hood closed, lock all doors by wireless operation.
S With any door or the engine hood open, close all doors and lock all doors and engine hood.
BE-139
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
HINT:
*1: Disarmed state (1) is the normal disarmed state.
*2: Disarmed state (2) is set from either the disarmed state (1) or the arming preparation state.
Disarmed state (1) *1
Performing any of the following will cause the system to
go into disarmed state (2).
D With ignition switch OFF, open any door or the engine
hood, and pull out key from ignition key cylinder.
D With ignition switch OFF, pull out key from ignition key
cylinder, and open any door or the engine hood.
Disarmed state (2) *2
Performing the following will cause the system Performing any of the following will
to go into arming preparation state. cause the system to return to disarmed
state (1).
All doors and engine hood are closed. D Unlock any door by wireless operation
D Unlock any door by key operation.
D Insert key into ignition key cylinder.
D Turn ignition switch from OFF to ON.
D Disconnect battery once, and then re-
connect it.
Arming preparation state
Performing any of the following will Performing the following will Performing any of the fol-
cause the system to return to dis- cause the system to go into lowing will cause the sys-
armed state (1). armed state. tem to return to disarmed
D Unlock any door by wireless op- state (2).
With all doors and engine
eration. Open any door or the
hood closed. Allow approx. 30
D Unlock any door by key operation. engine hood.
seconds to elapse.
D Insert key into ignition key cylin-
der.
D Turn ignition switch from OFF to
ON.
D Disconnect battery once, and
then reconnect it.
Continued from next page Continued on next page
BE-140
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
Continued on previous page Continued from
previous page
Armed state
Performing any of the following Performing any of the following will
will cause the system to return cause the system to set off the alarm.
to disarmed state (1).
D Unlock any door by wireless D Open any door and allow entry
operation. delay time*3 to elapse.
D Unlock any door by key op- D Open engine hood.
eration. D Disconnect battery once, and
D Insert key into ignition key then reconnect it.
cylinder and turn ignition D Directly connect ignition switch
switch from OFF to ON. without key (or turn ignition switch
ON without key).
Tampering is detected
Alarm sounding state
Alarm stops and system
Performing any of the following will When the system de-
returns to armed state.
cause the system to return to dis- tects tampering, the
armed state (1). horns sound and lights
D Unlock any door by wireless illuminate or flash in
operation. order to alert people
D Unlock any door by key opera- around the vehicle to
tion. the theft.
D Insert key into ignition key cyl- After approx. 60 se-
inder and turn ignition switch conds, alarm stops
from OFF to ON. and system returns to
armed state.
HINT:
*3: When any door is opened while all the doors are closed during pas-
sive arming mode, the entry delay time starts. If the switch condition
(armed state disarmed state (1) or (2)) is met during the entry delay
time, the theft deterrent system will return to disarmed state (1) or (2).
However, if the switch condition for disarmed state (1) or (2) is not met,
Alarm operation is cancelled. the theft deterrent system will recognize it as a theft and set off the alarm.
Entry delay time of 0, 15 or 30 seconds can be selected by the customiz-
ing function.
BE-141
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
4. FORCED DOOR LOCK CONTROL
(a) The forced door lock control prevents the vehicle from being tampered with. Immediately after a door
is unlocked (alarm starts), the door is forced to lock by a forced door lock signal.
(1) Conditions that force the doors to lock:
When no key is in the ignition key cylinder, the doors will be forced to lock if any of the following
conditions is met.
S The theft deterrent system is in the alarm sounding state of active arming mode.
S All the doors are locked. Any door is unlocked.
5. Indicator light output
Condition Indicator light
Disarmed state OFF
Arming preparation state ON
Armed state (Entry delay time) BLINK (ON)
Alarm sounding state ON
HINT:
Blinking frequency:
0.2 seconds (ON)
1.8 seconds (OFF)
6. PANIC ALARM CONTROL
(a) The panic alarm control makes it possible for you to voluntarily set off the panic alarm by pressing the
PANIC switch on the wireless transmitter. However, this control operates independently from the alarm
control by the theft deterrent system (switched to the alarm sounding state from the armed state).
(1) Conditions that cause the panic alarm control to set off the panic alarm:
The panic alarm control sets off the panic alarm by pressing the PANIC switch on the wireless
transmitter under the following conditions.
S The ignition switch is OFF.
S The theft deterrent system is not in the alarm sounding state (common to active arming
mode and passive arming mode).
S The panic alarm control is not operating (the alarm is not set off).
(2) Conditions that cause the panic alarm control to shut off the alarm:
The panic alarm control shuts off the panic alarm when any of the following conditions is met dur-
ing panic alarm operation.
S The ignition switch is turned ON.
S Either of the switches on the wireless transmitter (LOCK/UNLOCK) is pressed.
S The panic alarm ends (60 seconds have passed).
S The theft deterrent system switches to the alarm sounding state (common to active arming
mode and passive arming mode). However, the alarm is still sounding, because the theft
deterrent system has switched to the alarm sounding state. Conditions for canceling the
panic alarm are the same as for the alarm control.
HINT:
Active arming mode: See step 2
Passive arming mode: See step 3
BE-142
BODY ELECTRICAL - THEFT DETERRENT SYSTEM (Double Cab)
7. Switch to the active arming mode
HINT:
In each state of the passive arming mode, when the switch condition to the active mode (disarmed state of
active arming mode arming preparation state of active arming mode) is satisfied, the system will switch
to each state of the active arming mode. In this case, the active arming mode will continue until the system
switches to the disarmed state.
State of Passive Arming Mode Before Switch State of Active Arming Mode After Switch
Disarmed state Arming preparation state
Arming preparation state Arming preparation state (continuing for 30 seconds)
After alarming time has elapsed, the system will switch to the
Armed state (during entry delay time)
armed state
After alarming time has elapsed, the system will switch to the
Alarm sounding state
armed state
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo