Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra di ata750ea cip0705
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download cip0705 documenatation <<
Text preview - extract from the document
DIAGNOSTICS - AUTOMATIC TRANSMISSION (A750E/A750F for DI-1159
2UZ-FE)
DIDWJ-01
CIRCUIT INSPECTION
DTC P0705 Transmission Range Sensor Circuit Mal-
function (PRNDL Input)
CIRCUIT DESCRIPTION
The park/neutral position switch detects the shift lever position and sends signals to the ECM.
DTC No. DTC Detection Condition Trouble Area
(2-trip detection logic)
S All switches are OFF simultaneously for NSW, R, N, D, 3 and S Open or short in park/neutral position switch circuit
P0705 2 positions. S Park/neutral position switch
S 2 or more switches are ON simultaneously for NSW, R, D, 3 S ECM
and 2 positions.
MONITOR DESCRIPTION
These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral
position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that engine can be started
only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (NSW, R, D, 3 or
2).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position
signal simultaneously. The ECM will turn on the MIL and store the DTC.
MONITOR STRATEGY
Related DTCs P0705 Park/neutral position switch/Verify switch input
Required sensors/Components Park/neutral position switch
Frequency of operation Continuous
Condition (A) 2 sec.
Duration
D ti
Condition (B) 60 sec.
MIL operation 2 driving cycle
Sequence of operation None
TYPICAL ENABLING CONDITIONS
Specification
Item
It
Minimum Maximum
The monitor will run whenever this DTC is
See page DI-1128
not present.
Ignition switch ON
Battery voltage 10.5 V or more
DI-1160 DIAGNOSTICS - AUTOMATIC TRANSMISSION (A750E/A750F for
2UZ-FE)
TYPICAL MALFUNCTION THRESHOLDS
Detection criteria Threshold
One of the following conditions is met: Condition (A) or (B)
Condition (A)
Number of the following signal input at the same time 2 or more
NSW switch
R switch
D switch ON
3 switch
2 switch
Condition (B)
All of following conditions are met
N switch
NSW switch
R switch
OFF
D switch
3 switch
2 switch
COMPONENT OPERATING RANGE
Parameter Standard value
Park/neutral position switch The park/neutral position switch sends only one signal to the ECM.
DIAGNOSTICS - AUTOMATIC TRANSMISSION (A750E/A750F for DI-1161
2UZ-FE)
WIRING DIAGRAM
Double Cab:
P1
Park/Neutral Position SW ECM
8
P N L-R
To Starter Relay E6 STAR/NSW
5 4
J/C
B D
PL L-Y L-Y
J28 J29
6
H F 11
RL G-R R-B
J28 J29 E4 R
1
G G
NL LG-B LG-B
26 J28 J29
L 9
IE1 C C 21
2 RB DL W-R W-R
J28 J29 E4 D
7
E A 19
2L G-W L-W
J28 J29 E4 3
3
D B 10
LL P-L L
J28 J29 E4 2
8
L-B
To 4WD Control ECU
To Skid Control ECU with Actuator*1
To ABS Actuator with ECU*2
I23
Cowl Side J/B RH Ignition SW
7 GAUGE 4
B-Y IG1 AM1 W-L
1D 1C
8 IPO 7 2 1
F13 Cowl Side J/B LH
FL Block
ALT 1 AM1 6
B W
1L 1C
12 2 1 2
Battery
*1: w/ VSC
*2: w/o VSC
D14218
DI-1162 DIAGNOSTICS - AUTOMATIC TRANSMISSION (A750E/A750F for
2UZ-FE)
Except Double Cab:
P1
Park/Neutral Position SW ECM
8
N P L-R
To Starter Relay E6 STAR/NSW
5 4
J/C
B D
PL L-Y L-Y
J28 J29
6
H F 11
RL G-R G-R
J28 J29 E4 R
1
G G
NL LG-B LG-B
26 J28 J29
L 9
IE1 C C 21
2 RB DL W-R W-R
J28 J29 E4 D
7
L-B E A 19
2L G-W G-W
J28 J29 E4 3
3
2
D B 10
D8 LL P-L P-L
Diode J28 J29 E4 2
8
1
B-Y
E To ABS Actuator with ECM
J8
J/C To Skid Control ECM with Acrtuator*1
E To ABS Actuator with ECM*2
B-Y I23
Cowl Side J/B RH Ignition SW
9 GAUGE 2
B-Y IG1 AM1
1F 1L
4 2
Engine Room R/B W
B-L*3 ALT*3*4 AM1 7
B*4 W
2 2 IA9
1 21 2
Battery *1: w/ VSC
*2: w/o VSC
*3: 140A Towing Package
*4: 100A Except Towing Package
D14234
DIAGNOSTICS - AUTOMATIC TRANSMISSION (A750E/A750F for DI-1163
2UZ-FE)
INSPECTION PROCEDURE
HINT:
According to the DATA LIST displayed by the OBD II scan tool or hand-held tester, you can read the value
of the switch, sensor, actuator and so on without parts removal. Reading the DATA LIST as the first step of
troubleshooting is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the OBD II scan tool or hand-held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Push the "ON" button of the OBD II scan tool or the hand-held tester.
(f) When you use the hand-held tester:
Select the item "DIAGNOSIS / ENHANCED OBD II / DATA LIST".
(g) According to the display on the tester, read the "DATA LIST".
Measurement Item/
Item Normal Condition Diagnostic Note
Range (display)
When the shift lever position dis-
Shift lever position is; played on the hand-held tester dif-
PNP SW Status/
PNP SW [NSW] P and N: ON fers from the actual position, ad-
ON or OFF
Except P and N: OFF justment of the PNP switch or the
shift cable may be incorrect.
S Shift lever position is 2: OFF
PNP SW Status/
LOW S Shift position L switch Push: ON
ON or OFF
S Shift position L switch Push: OFF
Shift lever position is;
PNP SW Status/
2ND 2 and L: ON
ON or OFF
Except 2 and L: OFF
Shift lever position is;
PNP SW Status/
3RD 3: ON
ON or OFF
Except 3: OFF
Shift lever position is;
PNP SW Status/
DRIVE D: ON
ON or OFF
Except D: OFF
Shift lever position is;
PNP SW Status/
REVERSE R: ON
ON or OFF
Except R: OFF
DI-1164 DIAGNOSTICS - AUTOMATIC TRANSMISSION (A750E/A750F for
2UZ-FE)
1 Inspect park/neutral position switch.
Switch Side: PREPARATION:
(Connector Front View): (a) Jack up the vehicle.
(b) Disconnect the park/neutral position switch connector.
CHECK:
Measure the resistance according to the value(s) in the table
below when the shift lever is moved to each position.
OK:
P1 Shift Position Tester Connection Specified Condition
D14154
P 2 - 6 and 4 - 5 Below 1
Except P 10 k or higher
R 2-1 Below 1
Except R 10 k or higher
N 2 - 9 and 4 - 5 Below 1
Except N 10 k or higher
D 2-7 Below 1
Except D 10 k or higher
3 2-3 Below 1
Except 3 10 k or higher
2 2-8 Below 1
Except 2 10 k or higher
NG Replace park/neutral position switch
(See page AT-11).
OK
DIAGNOSTICS - AUTOMATIC TRANSMISSION (A750E/A750F for DI-1165
2UZ-FE)
2 Check harness and connector (Park/neutral position switch - ECM).
ECM: PREPARATION:
E7 E6 E5 E4 E3 (a) Connect the park/neutral position switch connector.
R(+) 2(+) (b) Turn the ignition switch ON.
CHECK:
Measure the voltage according to the value(s) in the table be-
low when the shift lever is moved to each position.
D(+) 3(+)
STAR/NSW(+)
D14155
OK:
Shift Position Tester connection Specified condition
P and N E6 - 8 (STAR/NSW) - Body ground Below 2 V
Except P and N 10 to 14 V
R E4 - 11 (R) - Body ground 10 to 14 V*
Except R Below 1 V
D E4 - 21 (D) - Body ground 10 to 14 V
Except D Below 1 V
3 E4 - 19 (3) - Body ground 10 to 14 V
Except 3 Below 1 V
2 and L E4 - 10 (2) - Body ground 10 to 14 V
Except 2 and L Below 1 V
HINT:
*: The voltage will drop slightly due to lighting up of the back up
light.
NG Repair or replace the harness or connector
(See page IN-30).
OK
Replace the ECM (See page SF-82).
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo