Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra di eg1grfe cip24192
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download cip24192 documenatation <<
Text preview - extract from the document
DI-345
DIAGNOSTICS - ENGINE (1GR-FE)
DIDU8-01
DTC P2419 Evaporate Emission System Switching
Valve Control Circuit Low
DTC P2420 Evaporate Emission System Switching
Valve Control Circuit High
CIRCUIT DESCRIPTION
Refer to the EVAP Inspection Procedure (see page DI-368).
Detection Detection
DTCs Monitoring Item DTC Detection Conditions Trouble Areas
Timing Logic
One of following conditions are met:
S 0.02 inch orifice low-flow
S 0.02 inch orifice high-flow
S Vacuum pump ON stuck S Pump module While
Vent valve stuck ON
P2419 S Vacuum pump OFF stuck S Connector/Wire harness Ignition
(Closed) 2 trips
S Vent valve ON (Closed) stuck (Pump module - ECM) switch
NOTE: S ECM OFF
P043E, P043F, P2401, P2402 and P2419
have same DTC detection conditions.
P2420 Vent valve stuck OFF (Vent) Vent valve OFF (Vent) stuck
WIRING DIAGRAM
Refer to the EVAP Inspection Procedure (see page DI-368).
DI-346
DIAGNOSTICS - ENGINE (1GR-FE)
MONITOR DESCRIPTION
5 hours* after the ignition switch is turned OFF, the electric vacuum pump creates negative pressure (vacu-
um) in the EVAP (Evaporative Emission) system. The ECM monitors for leaks and actuator malfunctions
based on the EVAP pressure.
HINT:
*: If the engine coolant temperature is not below 35_C (95_F) 5 hours after the ignition switch is turned off,
the monitor check starts 2 hours later. If it is still not below 35_C (95_F) 7 hours after the ignition switch is
turned off, the monitor check starts 2.5 hours later.
Sequence Operations Descriptions Duration
- ECM activation Activated by soak timer, 5 hours (7 or 9.5 hours) after ignition switch turned to OFF. -
Vent valve turned OFF (vent) and EVAP system pressure measured by ECM in order to
Atmospheric pressure register atmospheric pressure.
A 10 seconds
measurement If EVAP pressure is not between 70 kPa and 110 kPa (525 mmHg and 825 mmHg), ECM
cancels EVAP system monitor.
First 0.02 inch leak In order to determine 0.02 inch leak pressure standard, vacuum pump creates negative pres-
B pressure measure- sure (vacuum) through 0.02 inch orifice and them ECM checks if vacuum pump and vent 60 seconds
ment valve operate normally.
Vent valve turned ON (closed) to shut EVAP system.
Negative pressure (vacuum) created in EVAP system, and EVAP system pressure then
EVAP system pres-
C measured. 15 minutes*
sure measurement
Write down the measured value as it will be used in the leak check.
If EVAP pressure does not stabilize within 15 minutes, ECM cancels EVAP system monitor.
Purge VSV opened and then EVAP system pressure measured by ECM.
D Purge VSV monitor 10 seconds
Large increase indicates normal.
Second 0.02 inch leak Leak check is performed after second 0.02 inch leak pressure standard is measured.
E pressure measure- If stabilized system pressure higher than second 0.02 inch leak pressure standard, ECM 60 seconds
ment determines that EVAP system leaking.
F Final check Atmospheric pressure measured and then monitoring result recorded by ECM. -
* If only a small amount of fuel is in the fuel tank, it takes longer for the EVAP pressure to stabilize.
Operation A: Atmospheric Pressure Measurement Operation B: 0.02 Inch Leak Pressure Measurement
Canister
Fuel Tank
Vent Valve: OFF (vent) OFF OFF (vent)
Purge VSV: OFF
0.02 Inch Orifice
Pressure Sensor
Air Filter ON
Vacuum Pump: OFF Pump Module
Operation C: EVAP Leak Check Operation D: Purge VSV monitor
OFF ON (closed) ON ON (closed)
Atmospheric
Pressure
Negative
Pressure
ON ON
A23480
DI-347
DIAGNOSTICS - ENGINE (1GR-FE)
(a) P2419: Vent valve stuck ON (Closed)
In sequence B and E, to determine the leak criterion, the vacuum pump creates negative pressure in
the canister pump module through the 0.02 inch orifice. If the pressure is out of specified range or is
not saturated, the ECM illuminates the MIL and sets DTCs P043E, P043F, P2401, P2402 and P2419
(2-trip detection logic).
EVAP Pressure during EVAP Monitor
Purge VSV OFF OFF ON: Open
OFF: Closed
Vent Valve OFF OFF ON: Closed
OFF: Vent
Vacuum Pump ON ON
Malfunction
Malfunction
EVAP Pressure
-1 kPa OK OK
Specified Malfunction Malfunction
Range
-4.85 kPa
Sequence A B C D E
10 60 10 60
Time sec. sec.
Within 15 minutes
sec.
sec.
A23903
DI-348
DIAGNOSTICS - ENGINE (1GR-FE)
(b) P2420: Vent valve stuck OFF (vent)
In sequence C, the vent valve turns ON (closes) and the EVAP (Evaporative Emission) system pressure is
then measured by the ECM, using the pressure sensor, to conduct an EVAP leak check. If the pressure does
not increase when the vent valve turned ON (closed), the ECM interprets this as the vent valve being stuck
OFF (vent). The ECM illuminates the MIL and sets the DTC.
EVAP Pressure when Vent Valve Stuck OFF (vent):
Purge VSV ON ON: Open
OFF: Closed
Vent Valve ON ON: Closed
OFF: Vent
Vacuum Pump ON
EVAP Pressure
Positive
Negative
OK
First 0.02 inch
Leak Pressure
Standard
Malfunction
Sequence A B C D E
10 60 10 60
Time sec. sec.
Within 15 minutes
sec. sec.
A23666
MONITOR STRATEGY
P2419 Vent valve stuck open
Related DTCs
R l t d DTC
P2420 Vent valve stuck closed
Required sensors/components Vent valve
Frequency of operation Once per driving cycle
Duration Within 2 minutes
MIL operation 2 driving cycles
Sequence of operation None
TYPICAL ENABLING CONDITIONS
Specification
Item
It
Minimum Maximum
The monitor will run whenever these
See page DI-18
DTCs are not present
Atmospheric pressure 70 to 110 kPa (525 to 825 mmHg)
Battery voltage 10.5 V -
Vehicle speed - 2.5 mph (4 km/h)
Ignition switch OFF
EVAP pressure sensor malfunction (P450,
Not detected
P0452, P0453)
EVAP canister purge valve Not operated by scan tool
EVAP canister vent valve Not operated by scan tool
EVAP leak detection pump Not operated by scan tool
DI-349
DIAGNOSTICS - ENGINE (1GR-FE)
Both of the following conditions are met
Condition 1 and 2
before IG switch OFF
1. Duration that vehicle is driven 5 min. -
2. EVAP purge operation Performed
ECT 4.4 to 35◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo