Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra lu1grfe oaf insp
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download insp documenatation <<
Text preview - extract from the document
LU-1
LUBRICATION (1GR-FE) - OIL AND FILTER
OIL AND FILTER LU0Q8-01
Recommended Viscosity (SAE) INSPECTION
1. CHECK ENGINE OIL QUALITY
5W-30 (a) Check the oil for deterioration, water mixing, discoloring
or thinning.
(b) If the oil quality is visibly poor, replace it.
_C -29 -18 -7 4 16 27 38
_F -20 0 20 40 60 80 100 Oil grade:
A23190
ILSAC multigrade engine oil.
SAE 5W-30 is the best choice for good fuel economy,
and good starting in cold weather.
If SAE 5W-30 is not available, SAE 10W-30 may be
used. However, it should be replaced with SAE 5W-30
at the next oil replacement.
2. CHECK ENGINE OIL LEVEL
Check the engine oil level 5 minutes or more after the engine
has stopped.
If the engine is too hot, a false level will be read. The oil level
should be between the low and full level marks of the dipstick.
If it is below the low level mark, check for leakage and add oil
up to the full level mark.
NOTICE:
Do not fill with engine oil over the full level mark.
3. REMOVE OIL PRESSURE SWITCH ASSY
(a) Disconnect the oil pressure switch connector.
(b) Using a 24 mm deep socket wrench, remove the oil pres-
sure switch.
4. INSTALL OIL PRESSURE GAUGE
(a) Install the oil pressure gauge.
5. WARM UP ENGINE
6. CHECK OIL PRESSURE
Oil pressure:
At idle 29 kPa (0.3 kgfcm2, 4.3 psi) or more
294 to 588 kPa (3.0 to 6.0 kgfcm2, 43 to
At 3,000 rpm
Oil Pressure Gauge Oil Pressure Switch 85 psi)
A23126
7. INSTALL OIL PRESSURE SWITCH
Adhesive
(a) Remove the oil pressure gauge.
(b) Apply adhesive to 2 or 3 threads of the oil pressure switch.
Adhesive:
Part No. 08833-00080, THREE BOND 1344,
LOCTITE 242 or equivalent
P12478
LU-2
LUBRICATION (1GR-FE) - OIL AND FILTER
(c) Using a 24 mm deep socket wrench, install the oil pres-
sure switch.
Torque: 15 Nm (152 kgfcm, 11 ftlbf)
HINT:
Do not start the engine for 1 hour after installation.
(d) Connect the oil pressure switch connector.
8. START ENGINE AND CHECK FOR LEAKS
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo