Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra sa fah remo
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download remo documenatation <<
Text preview - extract from the document
SA-20
SUSPENSION AND AXLE - FRONT AXLE HUB
SA1JZ-02
REMOVAL
1. REMOVE FRONT WHEEL
2. REMOVE GREASE CAP
Using a screwdriver and hammer, remove the grease cap.
3. INSPECT FRONT AXLE HUB BEARING
(a) Remove the front disc brake caliper.
(b) Remove the front disc.
(c) Inspect the axle hub backlash.
(1) Using a dial indicator, check the backlash near the
center of the axle hub.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the maximum, replace the bearing.
cmc0311
(d) Inspect the axle hub deviation.
(1) Using a dial indicator, check the deviation at the sur-
face of the axle hub.
Maximum: 0.05 mm (0.0020 in.)
If the deviation exceeds the maximum, replace the bearing.
(e) Install the front disc.
(f) Install the front disc brake caliper.
(1) Install the brake caliper and 2 bolts.
cmc0312 Torque: 123 Nm (1,250 kgfcm, 90 ftlbf)
4. 4WD:
DISCONNECT DRIVE SHAFT
(a) Remove the cotter pin and lock cap.
(b) While applying the brakes, remove the lock nut.
R13426
5. w/ ABS:
DISCONNECT ABS SPEED SENSOR AND WIRE HAR-
NESS CLAMP FROM STEERING KNUCKLE
Remove the 2 bolts and disconnect the ABS speed sensor and
wire harness clamp from the steering knuckle.
F07263
SA-21
SUSPENSION AND AXLE - FRONT AXLE HUB
6. REMOVE BRAKE CALIPER AND DISC
(a) Remove the bolt and brake line clamp from the steering
knuckle.
(b) Remove the 2 bolts, brake caliper and disc.
NOTICE:
Do not damage the brake tube.
(c) Support the brake caliper securely.
7. REMOVE SHOCK ABSORBER (See page SA-63)
F07264
8. DISCONNECT LOWER BALL JOINT WITH LOWER
BALL JOINT DUST COVER PROTECTOR
Remove the 4 bolts and disconnect the lower ball joint with low-
er ball joint dust cover protector.
9. REMOVE STEERING KNUCKLE
(a) Remove the cotter pin and loosen the nut.
F07265
(b) Using SST, disconnect the steering knuckle.
SST 09950-40011 (09951-04010, 09952-04010,
SST
09553-04020, 09554-04010, 09955-04031,
09958-04011)
(c) Remove the nut and steering knuckle.
NOTICE:
4WD:
Be careful not to damage the oil seal and drive shaft boot.
R13196 HINT:
4WD:
When it is difficult to disconnect the drive shaft, tap the tip of the
drive shaft with a plastic hammer.
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo