Service Manuals, User Guides, Schematic Diagrams or docs for : . Car Manuals Toyota Tundra 2000-2006 Approved 04-06 techinfo.toyota.com ileaf 06toyrm 06toypdf 06rmsrc 06tundra rs saapatyp remo

<< Back | Home

Most service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.

Image preview - the first page of the document
remo

>> Download remo documenatation <<

Text preview - extract from the document

RS-49
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY (Power Adjuster Type)
RS127-01

REMOVAL
HINT:
S Use the same procedures for the RH side and LH side.
S The procedures listed below are for the LH side.
NOTICE:
S If the wiring connector of the SRS is disconnected
and the ignition switch is in the ON or ACC position,
DTCs will be recorded.
S Never use airbag parts from another vehicle. When
replacing parts, replace them with new ones.
1. PRECAUTION (SEE PAGE RS-1 AND RS-3)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the
airbag working.
3. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the 2 seat track covers.
HINT:
Tape the screwdriver tip before use.
4. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) Remove the front seat.
CAUTION:
Be careful not to damage the body.
5. REMOVE HEADREST

6. REMOVE SLIDE KNOB AND RECLINING KNOB
Using a screwdriver, remove the slide knob and reclining knob.
HINT:
Tape the screwdriver tip before use.

H24311

7. REMOVE SEAT CUSHION LOWER SHIELD, SEAT
CUSHION OUTER SHIELD AND SEAT CUSHION IN-
NER SHIELD
(a) Remove the screw from the seat cushion outer shield.
(b) Perform the same procedure as for the seat cushion inner
shield.

H24312
RS-50
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY (Power Adjuster Type)

H24313

(e) Remove the 2 screws from the seat cushion lower shield.
(f) Disconnect the lumbar switch connector from the lumbar
switch, and remove the seat cushion lower shield, outer
shield and inner shield.

H24314

(g) Remove the screw and separate the seat cushion lower
shield and seat cushion outer shield.
(h) Perform the same procedure as for the other side.
8. REMOVE FRONT SEAT INNER BELT
(a) Disconnect the wire harness clamps and connectors.
(b) Remove the nut and front seat inner belt.
9. REMOVE LUMBAR SWITCH
Remove the 2 screws and lumbar switch from the seat cushion
H24315 outer shield.
10. REMOVE POWER SEAT SWITCH
Remove the 3 screws and power seat switch.

11. REMOVE ARMREST ASSEMBLY
(a) Using a screwdriver, remove the armrest cap.
(b) Remove the bolt, armrest spacer, armrest lock plate and
armrest assembly.
(c) Remove the spacer from the armrest assembly.

H24316
RS-51
SUPPLEMENTAL RESTRAINT SYSTEM - SIDE AIRBAG ASSEMBLY (Power Adjuster Type)

12. REMOVE SEATBACK COVER AND PAD
(a) Remove the seatback cover belt from the seat frame as-
sembly.
(b) Open the fastener.

H24317

Hog Ring
H24321

(d) Remove the hog rings from the seat frame assembly.
(e) Remove the 2 headrest supports from the seat frame as-
sembly.
(f) Remove the seatback cover and pad from the seat frame
assembly.

Hog Ring H24318

◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo