Service Manuals, User Guides, Schematic Diagrams or docs for : . Rare and Ancient Equipment Unitc Copiers UNITC406 OPTIONS RE8_SM
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
>> Download RE8_SM documenatation <<
Text preview - extract from the document
DISPLAY EDITOR
(Machine Code: A997)
28 December 1993 SPECIFICATIONS
1. SPECIFICATIONS
Original Size: Maximum: A3 (lengthwise) or
11" x 17" (lengthwise)
(Scanned through the copier.)
Display: LCD (Monochrome), 8 gradations
640 x 480 dots
Zoom In/Out: 100% (33 dpi), 150% (50 dpi), 200% (67 dpi),
300% (100 dpi)
Display Speed: Less than 2 seconds
Editing: Screen and cursor
Power Consumption: 19.5W
Power Source: 5V/less than 1.5A and 24V/less than 10.5 from
the copier.
Dimensions (W x D x H): 280 x 232 x 50 mm
11.0" x 9.14" x 1.97"
Weight: less than 1.5 Kg or 33.1 lb
Remarks: The holder is required for installation.
Display Editor
1
OVERVIEW 28 December 1993
2. OVERVIEW
[B] [A]
[K]
[M]
[C] [D] [E] [F] [G] [H] [I] [J] [L]
The scanned image is sent to the display editor and displayed on the LCD
(640 x 480 dot).
By using the cursor [A], it is able to designate an area of the original image.
The display [B] shows 8 levels of grayscale, and the data communication
between the display editor and the IPU board is done by 3 bit parallel signal.
2
28 December 1993 EXPLANATION FOR EACH KEY
3. EXPLANATION FOR EACH KEY
Key Function
Scan Key [C] Sends the scan start command to the copier, and scanning of the
original is performed. After the scanning, the entire original image is
shown on the display editor (100%).
Full Image Key [D] The data scanned with 100 dpi is changed to about 33 dpi.
The entire A3 or DLT original image can be displayed.
Zoom 1 Key [E] The data scanned with 100 dpi is changed to 50 dpi. (150%
enlargement)
Zoom 2 Key [F] The data scanned with 100 dpi is changed to about 67 dpi. (200%
enlargement)
Zoom 3 Key [G] The data scanned with 100 dpi is displayed with about 100 dpi.
(300% enlargement)
Image Shift Key [H] Press to shift the image up and down, left and right by using the
cursor key according to the block diagram displayed at the lower left
corner.
Cursor Key [I] The cursor on the display will appear at the center after pressing the
scan key, zoom keys and image shift key. The cursor shown on the
display will move to the desired position by pressing this key.
Point Key [J] Sends the information of the current location of the cursor to the
copier.
Clear Key [K] The previously marked point before pressing the close key will be
canceled.
Close Key [L] Press to close an area.
All Clear Key [M] All specified dimensions or areas will be canceled.
Display Editor
3
INSTALLATION 28 December 1993
4. INSTALLATION
4.1 ACCESSORY CHECK
Check the accessories according to the following list:
Description Q'ty
1. Key Description Decal .....................................................................1
2. Cable ...............................................................................................1
3. Harness Clamp ................................................................................2
4. Truss Screw.....................................................................................4
4
28 December 1993 INSTALLATION
4.2 INSTALLATION PROCEDURE
[B]
[A]
[C]
CAUTION: When installing the display editor, make sure that the
copier is unplugged.
NOTE: Holder (A702) must be installed before starting the following
procedure.
1. Remove the front cover [A].
Display Editor
2. Install the display editor [B] (4 screws).
3. Remove the small cover [C].
5
INSTALLATION 28 December 1993
[G]
[D]
[F]
[E]
[H]
4. Install the 2 harness clamps [D] to the lower cover of the optional table.
5. Connect the cable [E] to the connector [F] of the display editor and to the
connector [G] of the copier.
6. Set the cable to the 2 wire cramps.
7. Plug in the power cord and turn on the main switch.
8. Enable the editor operation by selecting "Display" in the SP modes (page
4-11, No. 417 Editor).
9. Turn the main switch off and on.
10. Stick the key description decal [H] as necessary.
11. Check the machine operation.
6
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo