Service Manuals, User Guides, Schematic Diagrams or docs for : . Various LCD Panels Panel_SAMSUNG_SDI_S50HW-YD01_0_[DS]
<< Back |
HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download
Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing.
If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
Preview not available!
Sorry, no preview image available for this document.
Possible reasons are : this is not a PDF document, it is password protected or the file is partially corrupted.
We are working to fix the issue.
You can still download the full file from the link below and it will be viewable.
>> Download Panel_SAMSUNG_SDI_S50HW-YD01_0_[DS] documenatation <<Text preview - extract from the document Global LCD Panel Exchange Center www.panelook.com
SDI
STANDARD
CUSTOMER'S SPECIFICATIONS
(Approval Edition)
1,269cm (50 Inch) Wide Plasma Display Module
MODEL : S50HW-YD01
( NTSC / PAL )
* This specification will be approved by both Customer and Samsung SDI Co.,Ltd.
* Please return one of this specification with your signature for approval.
Proposed by: Approved by:
Signature Signature .
Vice President Sung Do Kim
Quality Innovation Team,
PDP Business Division,
SAMSUNG SDI CO.,LTD.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
Revision History
Revision Date Description Of Changes Rev. No Approval
1 2005-09-29 Newly established Rev.0.0 -
P7. 6.1 Display Performance
P21 10.3 Input Signal Definition
P24 10.5 LVDS Signal Pin Assignment
P28 10.8 Video Signal Interface Timing
2 2005-11-15 Rev. 1.0
Conditions
P34 10.11.9 Data Transfer Sequence(Read)
P39 12.2 Electrical Characteristic
Overview for Image Voltage
SAMSUNG SDI -2/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
TABLE OF CONTENTS
1. DESCRIPTION..............................................................................................................5
2. FEATURES ....................................................................................................................5
3. PRODUCT NAME AND MODEL NUMBER ............................................................5
4. FUNCTION OUTLINE.................................................................................................5
5. BLOCK DIAGRAM ......................................................................................................6
6. DISPLAY CHARACTERISTICS ................................................................................7
6.1 DISPLAY PERFORMANCE ............................................................................................................ 7
6.2 DISPLAY CELL ARRANGEMENT ................................................................................................. 8
6.3 LUMINANCE MEASUREMENT CONDITION .................................................................................. 9
6.4 CONTRAST MEASUREMENT CONDITION .................................................................................. 10
6.5 DISPLAY CELL DEFECT SPECIFICATION ................................................................................... 11
6.6 BRIGHTNESS VARIATION SPECIFICATION ............................................................................... 12
6.7 POWER CONSUMPTION ............................................................................................................ 13
6.8 GAMMA CHARACTERISTICS..................................................................................................... 15
7. SOUND PRESSURE LEVEL SPECIFICATION ...................................................16
7.1 MEASUREMENT CONDITION.................................................................................................... 16
7.2 SOUND PRESSURE LEVEL : ..................................................................................................... 16
8. MECHANICAL CHARACTERISTICS....................................................................17
8.1 MECHANICAL SPECIFICATIONS ............................................................................................... 17
8.2 MECHANICAL CHARACTERISTICS ........................................................................................... 17
9. ENVIRONMENTAL CONDITIONS ........................................................................18
9.1 OPERATIONAL ENVIRONMENTAL CONDITION ......................................................................... 18
9.2 STORAGE ENVIRONMENTAL CONDITION *1 ........................................................................... 18
9.3 PANEL SURFACE CONDITION ................................................................................................. 19
10. INTERFACE SIGNAL SPECIFICATIONS...........................................................20
10.1 CONFIGURATION CONTEXT ................................................................................................... 20
10. 2. INTERFACE FUNCTION SPECIFICATIONS (INPUT DATA AND DISPLAY PROCESSING) ........... 21
10. 3. INPUT SIGNAL DEFINITION.................................................................................................. 21
10. 4. LVDS SIGNAL DEFINITION AND FUNCTION ....................................................................... 22
10.5 LVDS SIGNAL PIN ASSIGNMENT .......................................................................................... 23
10.5 LVDS SIGNAL PIN ASSIGNMENT .......................................................................................... 24
10. 6 VIDEO SIGNAL DEFINITION AND FUNCTION ........................................................................ 26
10.7 ELECTRICAL CONDITION OF INTERFACE SIGNAL ................................................................. 27
10. 8 VIDEO SIGNAL INTERFACE TIMING CONDITIONS ................................................................ 28
10. 9 LVDS INTERFACE TIMING CONDITIONS .............................................................................. 30
10. 9 LVDS INTERFACE TIMING CONDITIONS .............................................................................. 31
10. 10 LVDS CONNECTION SPECIFICATIONS ............................................................................... 31
10. 11 I2C INTERFACE CONDITIONS ............................................................................................. 31
SAMSUNG SDI -3/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10. 11 I2C INTERFACE CONDITIONS ............................................................................................. 32
10. 12. CONNECTOR SPECIFICATIONS ........................................................................................... 36
11. ADDRESS MAP.........................................................................................................37
11.1 ADDRESS MAP........................................................................................................................ 37
11.2 DETAILS OF SETTINGS ........................................................................................................... 38
12. INPUT POWER VOLTAGE SPECIFICATIONS .................................................39
12.1 ELECTRICAL CHARACTERISTIC OVERVIEW FOR PDP MODULE VOLTAGES ......................... 39
12.2 ELECTRICAL CHARACTERISTIC OVERVIEW FOR IMAGE VOLTAGES ..................................... 39
12.3 OUT DIMENSION FOR REFERENCE ........................................................................................ 40
12.4 POWER APPLYING SEQUENCE ............................................................................................... 40
12.5 PIN ASSIGNMENT OF CONNECTORS FOR POWER SUPPLY ....................................................... 44
12.6 MECHANICAL OUT DRAWING ................................................................................................ 45
13. MECHANICAL DIMENSION DRAWING............................................................46
13.1. FRONT SIDE ........................................................................................................................... 46
13.2. REAR SIDE ............................................................................................................................. 47
13.2. REAR SIDE ............................................................................................................................. 47
14. LABEL ........................................................................................................................47
14. LABEL ........................................................................................................................48
14.1 LABEL TYPE ........................................................................................................................... 48
14.2 LABEL LOCATION ................................................................................................................... 48
14.2 LABEL LOCATION ................................................................................................................... 49
14.3 SERIAL NO.............................................................................................................................. 49
15. PACKING...................................................................................................................50
15.1 PACKING DIMENSION AND PARTS LIST.................................................................................. 50
15.2 PACKING ASSEMBLY DRAWING ............................................................................................ 51
16. RELIABLITY ............................................................................................................52
16.1 EXPECTED SERVICE LIFE ....................................................................................................... 52
16.2 DISCLAIMER .......................................................................................................................... 52
17. WARNING / CAUTION / NOTICE ........................................................................53
17.1 WARNING ............................................................................................................................... 53
17.2 CAUTION ................................................................................................................................ 54
17.3 NOTICE ................................................................................................................................... 55
SAMSUNG SDI -4/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
1. DESCRIPTION
The S50HW-YD01 is a 50-inch wide full color plasma display Module with a resolution of
1366(H) 768(V) pixels. The display module includes the Plasma Display Panel,
the Panel Driving Electronics, the Logic Control Board, and the Power Supply Unit(PSU).
2. FEATURES
x Wide aspect ratio(16:9) 50 inch diagonal display screen. The display area is 1106.46mm
wide and 622.08mm high.
x Slim and light weight. The display Module is 63.5mm in depth and weight only approx.
24.8kg include power supply.
x 68719.47 million colors(12Bit), 1073.7 million colors(10Bit), or 16.77 million
colors(8Bit) combination of R,G and B digital data.(according to LVDS input selection)
x High Luminance, High contrast, Wide viewing angle. The screen has a white peak
Luminance of Typical 1,200 cd/ (NTSC), Contrast of Typical 10,000:1(NTSC).
And a viewing angle of greater than 160 comparable to those of CRTs.
3. PRODUCT NAME AND MODEL NUMBER
x Product name : 50 inch Full Color Plasma Display Module3
(abbreviation : PDP Module3)
x Model number : S50HW-YD01
4. FUNCTION OUTLINE
x The plasma display Module has an APC(Automatic Power Control) function which
restricts power consumption within the certain value with regard to each display load
ratio.
x The plasma display Module is operated by following digital video signals; Vertical
synchronous signal, Horizontal synchronous signal, Enable signal and 8~12bits data
signal of each R,G, and B color. All signals are based on LVDS level.
x The plasma display Module is operated at 50Hz or 60Hz frame rate. An external frame
rate conversion is required in order to display the other formats.
x The plasma display Module requires several types of input power voltages ; voltage for
LOGIC, voltage for TCP, voltage for Gate Driver, voltage for Sustain, Address, Set,
Scan and X-bias.
x The plasma display Module is operated at progressive signal only.
An external progressive scan conversion is required in order to display the other formats.
x The plasma display Module requires rated 100~240V, 50~60Hz of input power voltage.
SAMSUNG SDI -5/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
5. BLOCK DIAGRAM
D-RAM Driver
R0 to R11
Timing
G0 to G11 Row
Driver
B0 to B11 LVDS Data Display 1366 768 Pixels X-Pulse
DCLK I/F contro- Data
Y-Pulse 1366 3 768 Cells Generat
Vsync ller Driver
Generator -or
Timing Scan
Hsync
contro- Timing
ENABLE
ller
Column Driver
Vcc Vdd Va Vs Ve Vset Vscan
AC Power
Source
Power Supply
(110/220V)
Figure-1. Block Diagram
SAMSUNG SDI -6/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6. DISPLAY CHARACTERISTICS
6.1 Display Performance
No Item Rating
1 Display Pixels Horizontal 1366 Vertical 768 pixels
(1 pixel = 1 R,G,B cells)
2 Display Cells Horizontal 4,098 Vertical 768 cells
3 Pixel Pitch Horizontal 810 Vertical 810
R Horizontal 270 Vertical 810
4 Cell Size G Horizontal 270 Vertical 810
B Horizontal 270 Vertical 810
5 Pixel Type R, G, B Non stripe (refer to Figure-2)
6 Effective Display Horizontal 1106.46 Vertical 622.08
Size [ 43.54 inch 24.49 inch ]
68719.47 million colors (12Bit)
7 Number of color 1073.7 million colors (10Bit)
16.77 million colors ( 8Bit)
Peak Luminance *1 NTSC : Typical 1,200 cd/
8 (peak algorithm on) PAL : Typical 1,100 cd/
Contrast Ratio *2 NTSC : Typical 10,000:1
9 (in dark room, PAL : Typical 5,000:1
peak algorithm on)
Brightness
10 NTSC / PAL : Typical 165 cd/
(Full white Brightness)
11 Viewing Angle *3 Over 160
(Note)
* 1. Luminance and Color Coordinates are the values that were measured with Full load
ratio white pattern. The condition for measurement is shown in Figure-3.
* 2. Contrast Ratio is calculated from the display Luminance and the non-display
Luminance value. Display condition is shown in Figure-4.
* 3. Viewing angle is a critical angle at which the Luminance is reduced to 50% to the
Luminance perpendicular to the PDP Module. The Luminance is measured by a non-
contact luminance meter CA-100Plus.
SAMSUNG SDI -7/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.2 Display Cell Arrangement
1st 2nd 3rd 1364th 1365th 1366th
Pixel Pixel Pixel Pixel Pixel Pixel
Column Column Column Column Column Column
Horizontal
Pixel Pitch
(0.810 )
1st Vertical
Pixel Pixel B G R B G R B G R B G R B G R B G R
Row Pitch
(0.810 )
2nd
Pixel B G R B G R B G R B G R B G R B G R
Row
767th
Pixel
Row B G R B G R B G R B G R B G R B G R
768th
Pixel
Row B G R B G R B G R B G R B G R B G R
Figure-2.Display Cell Arrangement
SAMSUNG SDI -8/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.3 Luminance Measurement Condition
(1) Display Pattern
Effective Display Area
345
Effective Display Area
78
345
614 138 614
Unit : Pixels(=lines)
marked area : White display area by maximum gradation setting
marked area : Black color (non-display area)
Figure-3. Display Pattern for Brightness & Contrast Ratio Measurement
(2) Display Area ratio : 1% white window
(3) Vsync : 16.7ms or 20ms
(4) Measuring equipment : MINOLTA CA-100Plus
Pattern Generator(VG-828, LVDS Output).
(5) Ambient Temperature : Room Temperature
(6) Ambient Luminance : Dark Room (<2 lux)
[ Note]
1. Measurement is done within 3 seconds after Power On. The temperature of panel before
measurement is room temperature (25 ).
SAMSUNG SDI -9/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.4 Contrast Measurement Condition
(1) Measuring point
Figure-4. Measurement point
(2) Vsync : 16.7 ms or 20ms
(3) Measuring Equipment : MINOLTA CA-100Plus
Pattern Generator(VG-828, LVDS Output).
(4) Contrast Calculation formula
Luminance of 1% white window Area at the center of the screen
Contrast ratio =
Luminance of Black Area *1
Note
1. For mass production test purposes, it is recommended to measure just 1 point,
P1 of Figure.-4 on display pattern of Fig.-3.
2. Measurement is done within 3 seconds after Power On. The temperature of
panel before measurement is room temperature (25 ).
(5) Ambient Light : Dark Room (<2 lux)
SAMSUNG SDI -10/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.5 Display Cell Defect Specification
In some cases, a panel may have defective cells that cannot be controlled.
These defective cells can be categorized into three types;
(1) Non-lighting cell defect : defect in which the cell is always off
(2) Non-extinguishing cell defect : defect in which the cell is always on.
(3) Flickering cell defect : defect in which the cell is flickering.
(4) High intensity cell defect : defect in which the cell is brighter than other cells
(5) Test Pattern : Full White, Full Red, Full Green and Full Blue with 1023 gray level.
The display cell defect specifications define the allowed limits for display cell defects and
are used as the criteria in determining whether a panel should be shipped.
Figure-5. Measurement Area
Specification
Item
Number of cell defects Distance between cell defects
Non-lighting Zone A: 4 and less
cell defect Zone B: 9 and less
Non-
Zone A: 2
extinguishing
Zone B: 3 and less
cell defect
Flickering Zone A: 2
cell defect Zone B: 3 and less Regardless of A and B zone,
Continuous Zone A: 1
Maximum 1 Cell Defect in an area of
Cell defect Zone B: 2
50mm*50mm is allowed.
Total number of cell defects
Total defect
Zone A and B is less than 16
SAMSUNG SDI -11/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.6 Brightness Variation Specification
The color-PDP uses ultraviolet light produced by gas discharge to illuminate phosphor.
Uneven phosphor coating and inconsistent discharge characteristics cause slight difference
Item Definition Specification
The brightness is measured at 9 points (A1~A9 of
Full white
Fig-6) on full white pattern. 10% and less
brightness
The full white brightness variation as then calculated
variation
from the following equations.
Max x x Min
Equation u 100% u 100%
x & x
in brightness among the sections in a panel.
The brightness variation specifications define the allowed limits for brightness differences
and the criteria in determining whether a panel is shipped.
W : Effective Display Area
A1 A2 A3 H * 0.1
H : Effective Display Area
A4 A5 A6
A7 A8 A9
H * 0.1
W * 0.1 W * 0.1
Figure-6. Measuring areas
SAMSUNG SDI -12/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.7 Power consumption
6.7.1 APC (Automatic Power Control) Function
The PDP has an APC (Automatic Power Control) function for the panel driver power
source. When the total display load ratio exceeds approximately 10%, total power
consumption is limited within a specified level(=Lower Power Limit) by APC function.
The operation behaviour of APC function is called as SLOW-APC. When the display
load-ratio changes from low to high value, the power-consumption rises instantly to
"Upper Power Limit" and gradually decreases until it reachs to the "Lower Power Limit".
Power
Upper Power
Limit
Power
Load-ratio
Lower Power
Limit
time t
Figure-7 Slow APC Behaviour
6.7.2 Brightness and Power Mode Control
This PDP module offsers two methods for Brightness and Power mode control.
APCO(APC Offset) is for Peak-Brightness control. APCO is register controllable through
I2C communication from image B'd.
1) Peak-Brightness Control( APCO)
- controls the max.sustain number
- APCO variable range : 00~C7h
Sustain
number
Max. Sustain
Normal Bright Mode (APCO=00h)
2/3 Peak-bright Mode (APCO=60h)
1/3 Peak-bright Mode (APCO=C7h)
Min. Sustain
Figure-8. APCO Behavior
0 Cmax load ratio 100%
SAMSUNG SDI -13/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.7.3 Power Consumption Specification
Upper : 390W
Lower : 370W
Slow APC Control System
Figure-9. Display load ratio vs. Power consumption
[Note]
1.This is the case that the PDP Module includes SDI's Main PSU at AC 100V, 60Hz.
It is measured on full screen white pattern with input gray-level 1024(10Bit) in module.
2. Power consumption is same for PAL and NTSC mode.
SAMSUNG SDI -14/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
6.8 Gamma characteristics
6.8.1 Basis of Gamma Curve
This PDP module is normally applied to the 2.0 gamma curve (refer to Figure-10)
But this specification could be modified on the request of the customer
Figure-10. Default Gamma Curve
SAMSUNG SDI -15/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
7. SOUND PRESSURE LEVEL SPECIFICATION
7.1 Measurement Condition
(1) Background Noise Level : less than 20dBA
(2) Measuring Pattern : Dynamic Images (only, Full Black to Full White)
(3) Measuring Equipment : Sound level meter Type 2827 made by B&K
(4) Measuring Distance : 1m from the rear side of PDP Module
(5) Measuring point
1M
Figure-11. Measuring Point
7.2 Sound Pressure Level :
Sound Pressure Level : Max.33dB (50Hz ~ 8kHz)
z Bandwidth : Octave
z Weighting Filter : A-weighting network
Note
1.PSU must be included in this measurement.
2.Measrurement pattern : Full White
SAMSUNG SDI -16/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
8. MECHANICAL CHARACTERISTICS
8.1 Mechanical Specifications
No Item Rating
Width 1,175 mm Height 682 mm Thickness 63.5 mm
Outer
1 (include FPC and TCP)
Dimension
*see Appendix : Mechanical Dimension Drawing
2 Weight Approximatly 24.8 kg
8.2 Mechanical Characteristics
No Item Rating
Frequency : 10 ~ 55 Hz
Sweep Rate : 1 Octave/min
1 Vibration
Stroke : x,y direction : 0.35 mm
Z direction : 0.175 mm
Acceleration : less than 20 G (x,y direction)
2 Shock less than 10 G (z direction)
Duration Time : 11 ms
* Notes: ( Test condition ) Non-Packaging, Operational (only for Vibration)
* Test time of Vibration Test is 30 minutes every direction(x,y,z)
* The number of times for shock test is 6 times every direction(x,y,z).
SAMSUNG SDI -17/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
9. ENVIRONMENTAL CONDITIONS
9.1 Operational Environmental Condition
No Item Rating
1 Ambient Display Operation *2 0 ~ 50
Temperature Temperature Slope Below 1.5 /minute
2 Panel Surface Small Size Pattern ~ 110
Temperature *3 Full White Pattern ~ 75
Temperature Slope Below 20 /cm
3 Humidity Display Operation *2 20 ~ 70 RH (no condensation)
4 Pressure Display Operation *2 1,013 ~ 845 hPa (0 ~ 2,000 m)
[NOTE]
1. Functional Operation means that the PDP module is operated only its electrical function.
2. Display Operation means that the PDP module is operated in its full specifications.
3. Panel Surface Temperature means the surface temperature of panel that is just increased
due to the loss of power inside Panel during the image display at a normal display mode
and a ambient temprature defined in this table.
The judgement of display defects (e.g. weak discharge, missing discharge) should be done
when the panel is operated at a ambient temperature defined in this table.
9.2 Storage Environmental Condition *1
No Item Rating
1 Ambient Temperature -20 ~ 70
2 Humidity 5 ~ 85 RH (no condensation)
3 Pressure 300 ~ 1,013 hPa (0~10,000m)
[NOTE]
1. Storage means the short term period. (e.g. transportation, relocation and so on)
SAMSUNG SDI -18/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
9.3 Panel Surface Condition
9.3.1. Panel surface temperature specification
The panel surface temperature should be kept as below in order to get stable display of
image.
- Tp= below 110 (Absolute Maximum Rating); when small size of image is displayed
- Tp= below 75 ; when Full White is displayed.
If the temperature exceeds above level, it may cause the defects of display image like
dot missing, line missing and/or poor image.
As the surface temperature of panel has tendency to rise with deduction of display rate,
the relation with temperature can be describe as below:
75 (display load rate is high : Large Area )
~ 110 (display load rate is low : Small Area)
Surface
Temperatur
110
75
15~20 100%
Displayed
Figure-12. Surface Temperature Vs Displayed Area
It is strongly recommended that the panel surface temperature should be kept as low as
possible, eventhought its maximium rating is descreibed as above.
9.3.2. Panel Surface Temperature for Breaking
The temperature uniformity across panel should be maintained below 20 / not to
occure panel breaking by temperature difference.
This breaking temperature is not absolute temperature, because it depends on condition
of panel production and panel scratch. Please take this value as a reference.
SAMSUNG SDI -19/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10. INTERFACE SIGNAL SPECIFICATIONS
10.1 Configuration Context
LVDS
decoder
SCALER LVDS (8bit) Drive IC
IC encoder
(8bit) LVDS
decoder
(4bit)
LVDS
decoder
SCALER LVDS (8bit) Drive IC
IC encoder
(10bit) LVDS
decoder
(4bit)
LVDS
decoder
SCALER LVDS (8bit) Drive IC
IC encoder
(12bit) LVDS
decoder
(4bit)
SAMSUNG SDI -20/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10.2. Interface Function Specifications (input data and display processing)
- 1366-dot data signals are inputted to this product to display data.
- The Video signal and control signal input section uses a low voltage differential
signaling (LVDS) interface.
- An I2C bus serial data interface is used for the communication between MPU of FTV
side and the CLU (Control LOGIC Module) of this PDP Module.
- I2C_READY signal is used that the CLU(Control LOGIC Unit) of PDP module inform
image scale b'd that CLU is ready for I2C communication.(1 : ready, 0 : not ready)
10.3. Input Signal Definition
N Item Signal name Q I/O Method Definition
o
1 Display Video RXIN0- 1 Input LVDS Differential serial data signal.
Signal Signal RXIN0+ 1 (LVDS1) Differentials Input video and timing
RXIN1- 1 signals after differential serial
RXIN1+ 1 conversation using a
RXIN2- 1 dedicated transceiver. The
RXIN2+ 1 serial data signal is
RXIN3- 1 transmitted seven times faster
RXIN3+ 1 than the base signal.
RXIN0- 1 Input
RXIN0+ 1 (LVDS2)
RXIN1- 1
RXIN1+ 1
Dot RXCLKIN- 1 Input LVDS Differential clock signal.
Clock RXCLKIN+ 1 (LVDS1) Differential Input the clock signal after
differential conversation
RXCLKIN- 1 Input using a dedicated transceiver.
RXCLKIN+ 1 (LVDS2) The clock signal is
transmitted at the same speed
as the base signal.
2 MPU Comm SDA 1 Input LVTTL I2C bus serial data
Commun unicat SCL 1 (I2C) communication signal.
ication ion I2C_READY 1 Communication with the
CLU (Control Logic Module)
of this product is enabled.
SAMSUNG SDI -21/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10.4. LVDS Signal Definition and Function
A video signal (display data signal and control signal) is converted from parallel data to
serial data with the LVDS transmitter and further converted into four sets of differential
signals before inputted to this PDP Module. These signals are transmitted seven times faster
than the dot clock signals. The dot clock signal is converted into one set of differential
signals.The LVDS signal definitions and functions are as follows (in Italic)::
( LVDS Default is 10Bit )
[8~12 Bit LVDS Interface]
Interface Signal Function
Symbol I/O Function Remarks
I Display Data Signal: LVDS signal
RxIN0- R0, R1, R2, R3, R4, R5, G0
RxIN0+ I LVDS signal
RxIN1- I Display Data Signal: LVDS signal
RxIN1+ I G1, G2, G3, G4, G5, B0, B1 LVDS signal
RxIN2- I Display Data Signal: LVDS signal
RxIN2+ I B2, B3, B4, B5, Hsync, Vsync, Enable LVDS signal
RxIN3- I Display Data Signal and Control Signal: LVDS signal
RxIN3+ I R6, R7, G6, G7, B6, B7 LVDS signal
RxCLKin- I Dot Clock Signal: LVDS signal
RxCLKin+ I CLK LVDS signal
SDA I I2C serial data 3.3V CMOS
SCL I Clock signal for SDA 3.3V CMOS
RESET I No LVDS No Picture Flag 3.3V CMOS
I2C Ready O It indicates CLU ready for communication 3.3V CMOS
[8Bit LVDS Interface]
Interface Signal Function
Symbol I/O Function Remarks
I Display Data Signal: LVDS signal
RxIN0- R2, R3, R4, R5, R6, R7,G2
RxIN0+ I LVDS signal
RxIN1- I Display Data Signal: LVDS signal
RxIN1+ I G3, G4, G5, G6, G7, B2, B3 LVDS signal
RxIN2- I Display Data Signal: LVDS signal
RxIN2+ I B4, B5, B6, B7, Hsync, Vsync, Enable LVDS signal
RxIN3- I Display Data Signal and Control Signal: LVDS signal
RxIN3+ I R8, R9, G8, G9, B8, B9 LVDS signal
RxIN0b- I Display Data Signal and Control Signal: LVDS signal
RxIN0b+ I R0, R1, G0, G1, B0, B1 LVDS signal
RxCLKin- I Dot Clock Signal: LVDS signal
RxCLKin+ I CLK LVDS signal
SDA I I2C serial data 3.3V CMOS
SCL I Clock signal for SDA 3.3V CMOS
RESET I No LVDS No Picture Flag 3.3V CMOS
SAMSUNG SDI -22/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
I2C Ready O It indicates CLU ready for communication 3.3V CMOS
[10Bit LVDS Interface]
Interface Signal Function
Symbol I/O Function Remarks
RxIN0- I Display Data Signal: LVDS signal
RxIN0+ I R4, R5, R6, R7, R8, R9, G4 LVDS signal
RxIN1- I Display Data Signal: LVDS signal
RxIN1+ I G5, G6, G7, G8, G9, B4, B5 LVDS signal
RxIN2- I Display Data Signal: LVDS signal
RxIN2+ I B6, B7, B8, B9, HYNC, VSYNC, DEN LVDS signal
RxIN3- I Display Data Signal and Control Signal: LVDS signal
RxIN3+ I R10, R11, G10, G11, B10, B11 LVDS signal
RxCLKIN- I Dot Clock Signal: LVDS signal
RxCLKIN+ CLK LVDS signal
I Display Data Signal: LVDS signal
RxIN0b-
R2, R3, G2, G3, B3, B3
RxIN0b+ LVDS signal
RxIN1b- Display Data Signal: LVDS signal
RxIN1b+ R0, R1, G0, G1, B0, B1 LVDS signal
RxCLKINb- Dot Clock Signal: LVDS signal
RxCLKINb+ CLKb LVDS signal
SDA I I2C serial data(Bi-direction) 3.3V CMOS
SCL I Clock signal for SDA 3.3V CMOS
RESET I No LVDS No Picture Flag 3.3V CMOS
I2C Ready O It indicates CLU ready for communication 3.3V CMOS
[12Bit LVDS Interface]
LVDS LVDS
Scaler IC encoder decoder Drive IC
(8bit) (8bit)
LVDS LVDS
encoder decoder
(8bit) (8bit)
Figure-14. LVDS 10bit application(Default)
SAMSUNG SDI -23/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10.5 LVDS Signal Pin Assignment
The table below indicates pin assignment of the LVDS IC(Receiver).
SAMSUNG SDI -24/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
SAMSUNG SDI -25/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10. 6 Video Signal Definition and Function
The table below indicates the definitions and functions of input video signals before LVDS conversion.
Interfaces Signal Functions
Symbol Function Remarks
Display data signal:
R11(7) to R0 12(8) bits red video signal (note 1)
R12(8): MSB*, R0: LSB**
Display data signal:
G11(7) to G0 12(8) bits green video signal (note 1)
G12(8): MSB*, G0: LSB**
Display data signal:
B11(7) to B0 12(8) bits blue video signal (note 1)
B12(8): MSB*, B0: LSB**
This signal specifies the data period for
Hsync Horizontal synchronous signal one horizontal line. Control of the next
line begins at the rising edge of Hsync.
Timing signal that controls the start of the
Vsync Vertical synchronous signal screen. Control of the next screen begins
at the rising edge of Vsync.
DCLK Clock for video signal Latch the video signal at falling edge.
* MSB: Most Significant Bit
**LSB: Least Significant Bit
Note 1: The RGB signal may be compensated with Inverse J circuit (E/D (=Error Diffusion)
must be included) before inputted to the PDP Module. In order to obtain good characteristic
of low level's gray scale, inverse J correction and E/D process are advisory to be performed
after inputted to the PDP Module.
Note 2 : Reommended Transmitter DS90CF385x2
SAMSUNG SDI -26/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10.7 Electrical Condition of Interface Signal
10.7. 1. Maximum Ratings
Common conditions : Ta = 25 , Vcc = 3.3V
Absolute Ratings
Item Parameter Symbol Ratings Module
Rx0-/+,Rx1-/+,Rx2-/+, Input Voltage Vi -0.3~3.6 V
LVDS Rx3-/+, Rx4/+, Input Current Ii -10~10
Input
CLKin-/+
Signals
3.3V SDA, SCL Input Voltage Vi -0.5~3.6 V
CMOS Input Current Ii -15
10.7. 2. Electrical Characteristics
Common conditions : Ta = 0 ~ +70 , Vcc = 3.0V ~ 3.6V
Electrical Characteristics
Signal Item Symbol Conditions Min. Typ. Max. Module
High level input
Vth VCM=1.2V - - 100
voltage
Low level input
LVDS Vtl VCM=1.2V -100 - -
voltage
VIN =
Input current Iin +2.4V/0V - - 20.0
Vcc = 3.6V
Vih 0.5*Vcc - 4.1 V
Input Voltage
Vil -0.5 - 0.3*Vcc V
Input Capacitance Vin - - - 8
I2C
Voh Ioh = 8 2.4 - - V
Output Voltage
Vol - - - 0.4 V
Output Current Iol - - - 10
High level input
Vih - 2.0 - - V
voltage
Low level input
Vil - GND - 0.8 V
voltage
3.3V VI=Vcc or
Input current Ii - - 10.0
CMOS GND
High level output
Voh Io = -1 2.4 - - V
voltage
Low level output
Vol Io = 1 - - 0.4 V
current
SAMSUNG SDI -27/61 - Rev.1.0 15/11/05
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SAMSUNG SDI Corporation Plasma Display Panel
10. 8 Video Signal Interface Timing Conditions
The table below indicates the conditions of input video signal before LVDS conversion. These
conditions must be satisfied. Refer to the figure of the timing chart.
8 bits LVDS ~12 bit LVDS belong to one timing table below.
Video Input Signal Timing (NTSC/PAL)
Symbol Timing Unit Remarks
- PAL long mode : below 48Hz
- PAL Normal Mode : 48 ~ 52Hz
- PAL LB Mode : 52 ~ 55 Hz
- NTSC lon
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo